C1622 Open or Short Circuit in Back Camera Signal
Diagnostic trouble codes · Vehicles built from Aug 2013
DESCRIPTION
This DTC is stored if the radio and display receiver assembly judges as a result of its self check that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1622 |
Open or Short Circuit in rear television camera signal |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY) |
Disconnect the R28 radio and display receiver assembly connector.
Disconnect the R25 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R28-11 (CA+) - R25-4 (CB+)
Always
Below 1 Ω
R28-12 (V+) - R25-2 (CV+)
Always
Below 1 Ω
R28-23 (CGND) - R25-3 (CGND)
Always
Below 1 Ω
R28-24 (V-) - R25-1 (CV-)
Always
Below 1 Ω
R28-11 (CA+) - Body ground
Always
10 kΩ or higher
R28-12 (V+) - Body ground
Always
10 kΩ or higher
R28-23 (CGND) - Body ground
Always
10 kΩ or higher
R28-24 (V-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY |
Disconnect the R28 radio and display receiver assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R28-23 (CGND) - Body ground
Always
Below 1 Ω
R28-24 (V-) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Component without harness connected
(Radio and Display Receiver Assembly)
|
|
||||
| OK | |
| 4. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY |
Disconnect the R25 rear television camera assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
R25-4 (CB+) - R25-3 (CGND)
Ignition switch ACC
5.5 to 7.05 V
Text in Illustration *a
Front view of wire harness connector
(to Rear Television Camera Assembly)
|
|
||||
| OK | |
| 5. CHECK REAR TELEVISION CAMERA ASSEMBLY |
Using an oscilloscope, check the waveform.


Text in Illustration *a
Component with harness connected
(Radio and Display Receiver Assembly)
*b
Waveform 1
*c
Waveform 2
*d
Synchronized Signal
*e
Video Waveform
-
-
Measurement Condition Item
Content
Tester Connection
R28-12 (V+) - R28-24 (V-)
Tool Setting
0.2 V/DIV., 50 μs/DIV.
Condition
- Waveform 1: Ignition switch ON, shift lever in R
- Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens
- OK:
- Waveform is as shown in illustration.
- HINT:
- The video waveform changes according to the image sent by the rear television camera assembly.
- Waveform 1: Ignition switch ON, shift lever in R
|
|
||||
| OK | ||
| ||
| 6. REPLACE REAR TELEVISION CAMERA ASSEMBLY |
Replace the rear television camera assembly with a new or normally functioning one (Click here).
| NEXT | |
| 7. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
Result Result
Proceed to
No DTC is output
A
DTC is output
B
|
|
||||
| A | ||
| ||
