2014 Hilux · Service Manual BODY ELECTRICAL

USB Audio System Recognition/Play Error

Circuit diagnosis · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

When a USB device or "iPod" is connected to the USB jack of the No. 1 stereo jack adapter assembly, it must have playable files. The device must also communicate with and be recognized by the radio and display receiver assembly. This diagnosis procedure is for when a device is not recognized, or files from the device cannot be played normally.

WIRING DIAGRAM

E278688E07

INSPECTION PROCEDURE

HINT:
  1. When a large amount of data is in a USB device, it may take a while to before play begins.
  2. When using a USB device, files that are copy protected or encrypted cannot be played.
  3. When files are not played in the sorted order, perform the following procedure before inspection.
    1. Add numbers in front of the file names.
    2. Put the files in a folder and copy the folder data to the USB device.
  4. When replacing the radio and display receiver assembly, it is necessary to perform the vehicle contract setting for T-Connect.


1. CHECK USB DEVICE OR "iPod"
  1. Disconnect the USB device or "iPod" from the No. 1 stereo jack adapter assembly.

  1. Check if playable files are present on the USB device or "iPod".

    HINT:
    Refer to System Description for playable files (Click here).

  1. Check if the USB device is a compatible format or "iPod" is a compatible version.

    HINT:
    Refer to System Description for compatible formats and versions (Click here).

    Result 
    Result
    Proceed to
    No playable files exist, or incompatible device format or version
    A
    Playable files exist, and compatible device format or version
    B



B
Go to step 2
A

USB DEVICE FORMAT WAS INCOMPATIBLE, "iPod" VERSION WAS INCOMPATIBLE, OR NO PLAYABLE FILES PRESENT

2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NO. 1 STEREO JACK ADAPTER ASSEMBLY)
  1. Disconnect the R30 radio and display receiver assembly connector.

  1. Disconnect the N14 No. 1 stereo jack adapter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R30-1 (USV1) - N14-1 (USV1)
    Always
    Below 1 Ω
    R30-2 (US1-) - N14-2 (US1-)
    Always
    Below 1 Ω
    R30-3 (US1+) - N14-3 (US1+)
    Always
    Below 1 Ω
    R30-4 (UGD1) - N14-4 (UGD1)
    Always
    Below 1 Ω
    R30-5 (USG1) - N14-5 (UJSS)
    Always
    Below 1 Ω
    R30-1 (USV1) - Body ground
    Always
    10 kΩ or higher
    R30-2 (US1-) - Body ground
    Always
    10 kΩ or higher
    R30-3 (US1+) - Body ground
    Always
    10 kΩ or higher
    R30-4 (UGD1) - Body ground
    Always
    10 kΩ or higher
    R30-5 (USG1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY (NO. 1 STEREO JACK ADAPTER ASSEMBLY POWER SOURCE)

  1. E278189E07
    Reconnect the R30 radio and display receiver assembly connector.

  1. Disconnect the No. 1 stereo jack adapter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N14-1 (USV1) - N14-4 (UGD1)
    Ignition switch ACC
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to No. 1 Stereo Jack Adapter Assembly)



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


4. FORMAT USB DEVICE OR RESTORE "iPod" AND RECHECK
  1. Delete all files in the USB device or "iPod" and format/ restore it.

    NOTICE:
    Formatting a USB device or restoring an "iPod" erases all music on the device. Make sure that back up music data is available before performing this operation.

  1. Save the data again and check if it can be played on the in-vehicle device.

    OK:
    Malfunction disappears.



NG
Go to step 5
OK

END (USB OR "iPod" IS DEFECTIVE)

5. REPLACE USB DEVICE OR "iPod"
  1. Turn the ignition switch off.

  1. Turn the ignition switch to ACC.

  1. Connect a known good USB device or "iPod" to the No. 1 stereo jack adapter assembly.

    HINT:
    1. If the malfunction occurred when a USB device was in use, use another USB device for the inspection. If the malfunction occurred when an "iPod" was in use, use another "iPod" for the inspection.
    2. Refer to System Description for compatible formats and versions (Click here).


NEXT


6. CHECK USB DEVICE OR "iPod"
  1. Check if USB device or "iPod" is recognized by radio and display receiver assembly, or if information such as track, artist and album names are displayed on screen.

    OK:
    USB device or "iPod" is recognized or track information such as track, artist and album names are displayed.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

USB DEVICE OR "iPod" WAS INCOMPATIBLE OR DEFECTIVE


← USB Audio System Recognition/Play Error (Aug 2012 – Jul 2013)Black Screen (Jun 2011 – Jul 2012) →