P064C Glow Plug Control Module
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Also covers:
- P066B Cylinder 1 Glow Plug Control Circuit High
- P066D Cylinder 2 Glow Plug Control Circuit High
- P066F Cylinder 3 Glow Plug Control Circuit High
- P0671 Cylinder 1 Glow Plug Circuit/Open
- P0672 Cylinder 2 Glow Plug Circuit/Open
- P0673 Cylinder 3 Glow Plug Circuit/Open
- P0674 Cylinder 4 Glow Plug Circuit/Open
- P067B Cylinder 4 Glow Plug Control Circuit High
- P166F Glow Plug Control Module Circuit Short
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (2 trip detection logic). |
Glow plug controller |
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Enter check mode |
A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (2 trip detection logic). |
|
WIRING DIAGRAM
Refer to DTC P052F (Click here)INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
P0671, P0672, P0673 and/or P0674 is output
A
P066B, P066D, P066F and/or P067B is output
B
P064C and/or P166F is output
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK GLOW PLUG CONTROLLER |
Disconnect the glow plug controller connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
G2-1(BATT) - Body ground
Always
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Glow Plug Controller)
Reconnect the glow plug controller connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR |
Disconnect connectors of the glow plug controller.

Remove the No. 1 glow plug connector from the glow plug.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G4-1 (GL1) - No. 1 glow plug connector terminal 1
Always
Below 1 Ω
G4-2 (GL2) - No. 1 glow plug connector terminal 2
Always
Below 1 Ω
G3-1 (GL3) - No. 1 glow plug connector terminal 3
Always
Below 1 Ω
G3-2 (GL4) - No. 1 glow plug connector terminal 4
Always
Below 1 Ω
Text in Illustration *1
No. 1 Glow Plug Connector
*a
Front view of wire harness connector
(to Glow Plug Controller)
*b
Front view of wire harness connector
(to Glow Plug Controller)
Reconnect the glow plug controller connector.
Reinstall the No. 1 glow plug connector.
|
|
||||
| OK | |
| 4. INSPECT GLOW PLUG |
Clear the DTCs (Click here).
Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.
Turn the ignition switch to ON.
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Read the DTCs.
Result Result
Proceed to
Same DTCs (that have been erased)
A
Other DTCs
B
- HINT:
- Check for DTCs in check mode.
|
|
||||
| B | |
| 5. REPLACE GLOW PLUG |
Replace the glow plug (Click here).
|
|
||||
| 6. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Confirm that the DTC is not output again.
- HINT:
- Check for DTCs in check mode.
| NEXT | ||
| ||
| 8. CHECK HARNESS AND CONNECTOR |
Disconnect connectors of the glow plug controller.

Remove the No. 1 glow plug connector from the glow plug.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G4-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground
Always
10 kΩ or higher
G4-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground
Always
10 kΩ or higher
G3-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground
Always
10 kΩ or higher
G3-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground
Always
10 kΩ or higher
- HINT:
- Make sure that there are no short circuits to the battery.
Text in Illustration *1
No. 1 Glow Plug Connector
*a
Front view of wire harness connector
(to Glow Plug Controller)
*b
Front view of wire harness connector
(to Glow Plug Controller)
Reconnect the glow plug controller connector.
Reinstall the No. 1 glow plug connector.
|
|
||||
| OK | |
| 9. REPLACE GLOW PLUG CONTROLLER |
Replace the glow plug controller (Click here).
|
|
||||
| 10. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Confirm that the DTC is not output again.
- OK:
- No DTC is output.
- HINT:
- Check for DTCs in check mode.
|
|
||||
| OK | ||
| ||
| 12. REPLACE GLOW PLUG |
Replace the glow plug (Click here).
|
|
||||
| 13. CHECK HARNESS AND CONNECTOR |
Disconnect connectors of the glow plug controller.

Remove the No. 1 glow plug connector from the glow plug.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G4-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground
Always
10 kΩ or higher
G4-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground
Always
10 kΩ or higher
G3-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground
Always
10 kΩ or higher
G3-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground
Always
10 kΩ or higher
- HINT:
- Make sure that there are no short circuits to the battery.
Text in Illustration *1
No. 1 Glow Plug Connector
*a
Front view of wire harness connector
(to Glow Plug Controller)
*b
Front view of wire harness connector
(to Glow Plug Controller)
Reconnect the glow plug controller connector.
Reinstall the No. 1 glow plug connector.
|
|
||||
| OK | |
| 14. REPLACE GLOW PLUG CONTROLLER |
Replace the glow plug controller (Click here).
|
|
||||
| 15. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 16. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON.
Turn the tester on.
Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).
Confirm that the DTC is not output again.
- HINT:
- Check for DTCs in check mode.
| NEXT | ||
| ||
