2014 Hilux · Service Manual ENGINE

P064C Glow Plug Control Module

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

P064C 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
The MOS inside the glow plug control unit is detected as being stuck on 3 times while the glow plugs are on (2 trip detection logic).
Glow plug controller
P066B 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 1 glow plug
  3. Short in No. 1 glow plug circuit
P066D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 2 glow plug
  3. Short in No. 2 glow plug circuit
P066F 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 3 glow plug
  3. Short in No. 3 glow plug circuit
P067B 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 4 glow plug
  3. Short in No. 4 glow plug circuit
P0671 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 1 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 1 glow plug
  3. Open in No. 1 glow plug circuit
P0672 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 2 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 2 glow plug
  3. Open in No. 2 glow plug circuit
P0673 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 3 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 3 glow plug
  3. Open in No. 3 glow plug circuit
P0674 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
An open circuit in the No. 4 glow plug circuit is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. No. 4 glow plug
  3. Open in No. 4 glow plug circuit
P166F 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Enter check mode
A short circuit in a wire harness between the glow plugs is detected 3 times while the glow plugs are on (2 trip detection logic).
  1. Glow plug controller
  2. Open or short in glow plug circuit

WIRING DIAGRAM

Refer to DTC P052F (Click here)

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0671, P0672, P0673 and/or P0674 is output
    A
    P066B, P066D, P066F and/or P067B is output
    B
    P064C and/or P166F is output
    C



B
Go to step 8

C
Go to step 13
A


2. CHECK GLOW PLUG CONTROLLER

  1. A241159E04
    Disconnect the glow plug controller connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    G2-1(BATT) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR

  1. A249251E02
    Disconnect connectors of the glow plug controller.

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G4-1 (GL1) - No. 1 glow plug connector terminal 1
    Always
    Below 1 Ω
    G4-2 (GL2) - No. 1 glow plug connector terminal 2
    Always
    Below 1 Ω
    G3-1 (GL3) - No. 1 glow plug connector terminal 3
    Always
    Below 1 Ω
    G3-2 (GL4) - No. 1 glow plug connector terminal 4
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    No. 1 Glow Plug Connector
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)
    *b
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 glow plug connector.



NG
Go to step 6
OK


4. INSPECT GLOW PLUG
  1. Clear the DTCs (Click here).

  1. Exchange the glow plugs of the malfunctioning cylinders (the cylinders indicated by output DTCs) with the glow plugs of normally functioning cylinders.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    Same DTCs (that have been erased)
    A
    Other DTCs
    B

    HINT:
    Check for DTCs in check mode.



A
Go to step 14
B


5. REPLACE GLOW PLUG
  1. Replace the glow plug (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END

8. CHECK HARNESS AND CONNECTOR

  1. A249251E02
    Disconnect connectors of the glow plug controller.

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G4-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground
    Always
    10 kΩ or higher
    G4-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground
    Always
    10 kΩ or higher
    G3-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground
    Always
    10 kΩ or higher
    G3-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.

    Text in Illustration 
    *1
    No. 1 Glow Plug Connector
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)
    *b
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 glow plug connector.



NG
Go to step 10
OK


9. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here).



NEXT
Go to step 11
10. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    OK:
    No DTC is output.

    HINT:
    Check for DTCs in check mode.



NG
Go to step 12
OK

END

12. REPLACE GLOW PLUG
  1. Replace the glow plug (Click here).



NEXT
Go to step 16
13. CHECK HARNESS AND CONNECTOR

  1. A249251E02
    Disconnect connectors of the glow plug controller.

  1. Remove the No. 1 glow plug connector from the glow plug.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G4-1 (GL1) or No. 1 glow plug connector terminal 1 - Body ground
    Always
    10 kΩ or higher
    G4-2 (GL2) or No. 1 glow plug connector terminal 2 - Body ground
    Always
    10 kΩ or higher
    G3-1 (GL3) or No. 1 glow plug connector terminal 3 - Body ground
    Always
    10 kΩ or higher
    G3-2 (GL4) or No. 1 glow plug connector terminal 4 - Body ground
    Always
    10 kΩ or higher

    HINT:
    Make sure that there are no short circuits to the battery.

    Text in Illustration 
    *1
    No. 1 Glow Plug Connector
    *a
    Front view of wire harness connector
    (to Glow Plug Controller)
    *b
    Front view of wire harness connector
    (to Glow Plug Controller)

  1. Reconnect the glow plug controller connector.

  1. Reinstall the No. 1 glow plug connector.



NG
Go to step 15
OK


14. REPLACE GLOW PLUG CONTROLLER
  1. Replace the glow plug controller (Click here).



NEXT
Go to step 16
15. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


16. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Using the intelligent tester, switch the ECM from normal mode to check mode (Click here).

  1. Confirm that the DTC is not output again.

    HINT:
    Check for DTCs in check mode.


NEXT

END


← P064C Glow Plug Control Module (+ 9 more codes) (Aug 2013 – Jul 2014)P0724 Brake Switch "B" Circuit High (Jun 2011 – Jul 2012) →