2014 Hilux · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jun 2011


1. INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
  1. Attach the 3 claws to install the radiator grille (or front panel) emblem.


2. INSTALL RADIATOR GRILLE MOULDING
  1. Attach the 18 claws to install the radiator grille moulding.

  1. Install the 7 screws.


3. INSTALL NO. 1 RADIATOR GRILLE SEAL

HINT:
When installing the No. 1 radiator grille seal, heat the radiator grille using a heat light.

Standard:
Item
Temperature
Radiator Grille
20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the radiator grille excessively.

  1. Clean the radiator grille surface.

    1. Using a heat light, heat the radiator grille surface.

    2. Remove the double-sided tape from the radiator grille surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new No. 1 radiator grille seal.

    1. Remove the peeling paper from the face of a new No. 1 radiator grille seal.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Attach the 13 clips to install the No. 1 radiator grille seal.


4. INSTALL NO. 1 LOWER RADIATOR GRILLE
  1. Attach the 13 claws to install the No. 1 lower radiator grille.


5. INSTALL FRONT BUMPER HOLE COVER LH
  1. Attach the 3 claws to install the front bumper hole cover.


6. INSTALL FRONT BUMPER HOLE COVER RH

HINT:
Use the same procedure described for the LH side.


7. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)
  1. Install the fog light assembly LH with the 3 bolts.


8. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedure described for the LH side.


9. INSTALL NO. 1 HEADLIGHT CLEANER HOSE (w/ Headlight Cleaner System)
  1. Attach the 3 clamps to install the No. 1 headlight cleaner hose to the front bumper cover.


10. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
  1. Attach the 2 claws to install the headlight washer actuator sub-assembly LH with the bolt.

    Torque:
    1.1 N*m{ 11 kgf*cm , 10 in.*lbf }

  1. Connect the headlight cleaner hose.


11. INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


12. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY LH (w/ Headlight Cleaner System)

  1. E229389
    Attach the 2 claws to install the type 1 headlight washer nozzle sub-assembly LH.


13. INSTALL TYPE 1 HEADLIGHT WASHER NOZZLE SUB-ASSEMBLY RH (w/ Headlight Cleaner System)

HINT:
Use the same procedure described for the LH side.


14. INSTALL FRONT BUMPER EXTENSION LH (w/ Outside Moulding)
  1. Install the front bumper extension with the 8 retainers.


15. INSTALL FRONT BUMPER EXTENSION RH (w/ Outside Moulding)

HINT:
Use the same procedure described for the LH side.

← DISASSEMBLY (from Jun 2011)INSTALLATION (from Jun 2011) →