Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(w/ EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052067 ECD SYSTEM(w/ EGR Cooler) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  P1238  Injector Malfunction  


DESCRIPTION

HINT:
·

For more information on the injector assemblies and common rail system, refer to System Description (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>SYSTEM DESCRIPTION).

·

If DTC P1238 has been stored, refer to Diagnostic Trouble Code Chart (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DIAGNOSTIC TROUBLE CODE CHART).



The ECM detects combustion deterioration for a specific cylinder.

A303107
1.208,1.083 1.604,1.26 false 1.719,2 2.052,2 false 1.385,3.948 1.719,3.948 false 0.125,0.073 0.438,0.271 0.313,0.198 10 false *A 1.052,1 1.365,1.198 0.313,0.198 10 false *1 2.146,1.906 2.458,2.104 0.313,0.198 10 false *2 1.198,3.885 1.51,4.083 0.313,0.198 10 false *3
*A Injector Cross Section Diagram:
*1 Solenoid Valve
*2 Piston
*3 Nozzle Needle


HINT:
·

The cylinder which has the compensation value, indicated by Injection Feedback Val #1, #2, #3 and #4, that varies from the other cylinders may be malfunctioning.

·

If DTC P0093 (fuel leaks from high-pressure area) is stored simultaneously, a leakage malfunction of a specific cylinder has probably occurred.

·

If DTC P0200 (open or short in the injector driver or injector circuit) is stored simultaneously, there is probably a faulty circuit located between the ECM and the injector assembly including the injector driver.

·

If only DTC P1238 (injector malfunction) has been stored, an injector assembly mechanical malfunction or insufficient compression (valve clearance, etc.) has probably occurred. An open or short malfunction of the ECM, injector driver or injector circuit is unlikely.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1238 Injector Malfunction A large engine speed fluctuation when idling continues for 60 seconds (2 trip detection logic).
Main Trouble Area
·

Injector assembly

·

Injector driver (P0200 stored simultaneously)

·

Connector connection (P0200 stored simultaneously)

·

Compression pressure


Related Trouble Area
·

Valve timing

·

Fuel with low cetane number used

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P1238
·

Injection Volume

·

Injection Feedback Val #1 to #4

·

Fuel Press

·

Target Common Rail Pressure



HINT:
·

If DTC P1238 is stored, the following symptoms may appear:

·

Rough idle

·

Poor driveability


·

After confirming DTC P1238, check the internal fuel pressure on the intelligent tester by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press, Target Common Rail Pressure.

Under a stable condition such as idling or running the engine at 2500 rpm without load, Fuel Press is within 5000 kPa of Target Common Rail Pressure.



CONFIRMATION DRIVING PATTERN

P1238
DTC Detection Drive Pattern Warm up the engine and idle it for 60 seconds

MONITOR DESCRIPTION

P1238 (Injection malfunction, except open or short in injector circuit):

This DTC will be stored if the engine speed fluctuation between each cylinder is large. The ECM monitors changes in the crankshaft rotation speed using the crankshaft position sensor in order to detect improper combustion. The camshaft position sensor also plays a role in determining which cylinder has the problem. The fluctuation counter increases when irregular crankshaft rotation speed variation exceeds the threshold with the engine idling. Therefore, if any one of the cylinders is operating poorly (rough idle), the ECM stores this DTC.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION).



HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

When this DTC is stored, be sure to carefully examine "Injection Feedback Val #1 to #4", "Injection Volume", "Fuel Press", "Target Common Rail Pressure", "Engine Speed", "MAF", "Coolant Temp" and "Vehicle Speed" in the freeze frame data.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1238)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P1238 is output A
P1238 and other DTCs are output B



HINT:
·

If any DTCs other than P1238 are output, troubleshoot those DTCs first.

·

If DTCs other than P1238 are not output, check the fuel condition before proceeding to the next step.




A

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)

B

2.CHECK HARNESS AND CONNECTOR (ENGINE WIRE HARNESS)
a.

Check the wire harness and connector connections.

OK:

The wire harness and connectors have been connected securely and there are good connections.



Result:
Proceed to
OK
NG



OK

3.CHECK INJECTOR COMPENSATION CODE

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation codes.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION

OK:

Compensation codes stored in the ECM match compensation codes of the installed injector assemblies.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)

NG

9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
4.READ VALUE USING INTELLIGENT TESTER (COMPENSATORY INJECTION VOLUME FOR EACH CYLINDER)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Injection Feedback Val #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
50003 61 368,369,370,371

d.

Read the value.

Standard value:

The compensatory injection volume is less than 3.0 mm3/st


HINT:
·

If the fuel injector assembly is malfunctioning, the compensatory injection volume remains at 5.0 mm3/st.

·

If there is a disconnection, the feedback value will increase and +5.0 mm3/st will be indicated, because it will become impossible for the injector assembly to inject.




e.

Inspect and repair the cylinder that has an improper compensation value according to the following steps.


Result:
Proceed to
NEXT



NEXT

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE CYLINDER #1 TO #4 FUEL CUT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Cylinder #1 to #4 Fuel Cut.

Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231

d.

Check the 4 cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
6.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER
HINT:

Measure the compression of the cylinder that had a high speed during the "Check the Cylinder Compression" Active Test.


a.

Check the cylinder compression pressure.

Click hereEngine / Hybrid System>2KD-FTV ENGINE MECHANICAL>ENGINE>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPLACE INJECTOR ASSEMBLY

NG

14.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
7.REPLACE INJECTOR ASSEMBLY
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>2KD-FTV FUEL>FUEL INJECTOR(w/o DPF)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

8.BLEED AIR FROM FUEL SYSTEM
8.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
9.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING
a.

b.

Perform the injector pilot quantity learning.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION


Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P1238)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the pending DTCs.

HINT:
·

If no pending DTCs are output, proceed to the next step to check "All Readiness".

·

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.



i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1238.


iii.

Check the DTC judgment result.

Result:
Tester Display Result Proceed to
Pending DTC P1238 is output A
All Readiness ABNORMAL
NORMAL B


HINT:

If STATUS is INCOMPLETE or N/A, increase the idling time.





A

11.REPLACE ECM

B

END

11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher) and idle it for 60 seconds (the shift lever should be in neutral, and the A/C switch and all accessory switches should be off).


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P1238.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, increase the idling time.



Result:
Proceed to
NEXT



NEXT

END

14.CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED