Home › Engine / Hybrid System › 2KD-FTV FUEL › FUEL INJECTOR(w/o DPF) › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009578 2KD-FTV FUEL _0052215 FUEL INJECTOR(w/o DPF) A

2KD-FTV FUEL  FUEL INJECTOR(w/o DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.DRAIN ENGINE COOLANT (w/ EGR Cooler)

Hide 4.REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler)

Hide 5.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o EGR Cooler)

Hide 6.CHECK INJECTOR COMPENSATION CODE

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions.



b.

Check that the compensation code of the installed injector is the same as the code registered in the ECM. If the code is not the same, register the injector compensation code on the injector.



Hide 7.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

Hide 8.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

Hide 9.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
·

After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.

·

After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



a.
A301675

w/ EGR Cooler:

i.

Remove the 2 nuts and No. 3 injection pipe clamp.


ii.
A301676

Remove the 2 bolts and 2 No. 2 injection pipe clamps.


iii.
A153266
0.087,0.145 0.272,0.3 0.185,0.155 10 *a 0.087,2.279 0.272,2.434 0.185,0.155 10 *b
*a Injector Side
*b Common Rail Side


Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



b.
A231803
2.188,0.115 1.969,0.115 1.969,0.115 1.969,1.448 true 1.385,4.188 1.385,4.083 1.385,4.083 1.656,3.49 true 2.25,0.021 2.615,0.271 0.365,0.25 10 false *1 1.313,4.24 1.625,4.49 0.313,0.25 10 false *2 0.083,0.063 0.271,0.219 0.188,0.156 10 false *a 0.094,2.354 0.281,2.51 0.188,0.156 10 false *b
*1 No. 2 Injection Pipe Clamp
*2 No. 3 Injection Pipe Clamp
*a Injector Side
*b Common Rail Side


w/o EGR Cooler:

i.

Remove the bolt and No. 2 injection pipe clamp.


ii.

Remove the 2 nuts and No. 3 injection pipe clamp.


iii.

Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



Hide 10.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

Hide 11.DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)

Hide 12.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)

Hide 13.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)

Hide 15.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

Hide 16.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:

If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection pipe clamp with a new one.


a.

w/ EGR Cooler:

i.
A152275

Remove the bolt and disconnect the injection pipe clamp.


ii.
A152276
0.129,0.087 0.314,0.242 0.185,0.155 10 *a 0.129,2.423 0.314,2.578 0.185,0.155 10 *b
*a Injector Side
*b Common Rail Side


Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



b.

w/o EGR Cooler:

i.
A098893

Remove the 2 bolts and disconnect the 2 injection pipe clamps.


ii.
A231804
0.125,0.104 0.313,0.26 0.188,0.156 10 false *a 0.125,2.448 0.313,2.604 0.188,0.156 10 false *b
*a Injector Side
*b Common Rail Side


Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



Hide 17.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:

If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.


a.
A152277

w/ EGR Cooler:

Remove the 3 bolts and disconnect the 4 injector connectors.


b.

w/o EGR Cooler:

Disconnect the 4 injector connectors.


c.

Disconnect the ventilation hose.


d.
A060180

Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.


e.
G034877

Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.


f.
A289511

Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


Hide 19.REMOVE INJECTOR ASSEMBLY

a.
A060184
0.26,1.115 0.49,0.531 0.49,0.531 0.604,0.531 true 0.667,0.427 0.979,0.625 0.313,0.198 10 false *1
*1 Union Bolt


Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.

NOTICE:
·

When removing the nozzle leakage pipe, place a cushion under the pipe.

·

Be careful not to deform or scratch the union seal surface.

·

After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.




b.
G034876

Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.

HINT:

Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.



c.

Remove the O-ring from each injector.


d.

Remove the 4 injection nozzle seats from the cylinder head.