Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0116  Engine Coolant Temperature Circuit Range / Performance Problem  


DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.

The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0116 Engine Coolant Temperature Circuit Range / Performance Problem Condition 1:
When engine is started cold and warmed up, the engine coolant temperature sensor value does not change (2 trip detection logic).
Condition 2:
After the warmed up engine is stopped and the next cold engine start is performed, the engine coolant temperature sensor value does not change (2 trip detection logic)
·

Thermostat

·

Engine coolant temperature sensor


Comes on DTC stored

Related Data List
DTC No. Data List
P0116 Coolant Temp

HINT:

If DTC P0116 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

P0116
DTC Detection Drive Pattern With the engine coolant temperature below 60°C (140°F), start the engine and idle it for 5 minutes. Then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more and check that the engine coolant temperature changes by 1°C (1.8°F) or more.

MONITOR DESCRIPTION

Engine coolant temperature sensor cold start monitor

When a cold engine start is performed and then the engine is warmed up, if the engine coolant temperature sensor value does not change, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


Engine coolant temperature sensor soak monitor

If the engine coolant temperature sensor value does not change after the warmed up engine is stopped and then the next cold engine start is performed, it is determined that a malfunction has occurred. If this is detected in 2 consecutive driving cycles, the MIL is illuminated and a DTC is stored.


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0116)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P0116 is output A
P0116 and other DTCs are output B




A

2.INSPECT THERMOSTAT

B

2.INSPECT THERMOSTAT
a.

b.

Measure the valve opening temperature of the thermostat.

Standard opening temperature:

80 to 84°C (176 to 183°F)


HINT:

In addition to the above check, confirm that the valve is completely closed when the temperature is below the standard.




Result:
Proceed to
OK
NG



OK

3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR

NG

4.REPLACE THERMOSTAT
3.REPLACE ENGINE COOLANT TEMPERATURE SENSOR
a.

Replace the engine coolant temperature sensor.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.REPLACE THERMOSTAT
4.REPLACE THERMOSTAT
a.

Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Powertrain > Engine > Data List
Tester Display
Coolant Temp
50003 61 309

d.

Check that the engine coolant temperature is 60°C (140°F) or less.


e.

Start the engine.


f.

Idle the engine for 5 minutes, and then drive the vehicle at a speed of 40 km/h (25 mph) or more for a total of 5 minutes or more.


g.

Check that the engine coolant temperature changes by 1°C (1.8°F) or more.


Result:
Proceed to
NEXT



NEXT

END