Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P2453  Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor assembly and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

If P2453 is present, refer to the DTC chart for DPF system (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).



A128654
4.427,1.167 4.24,1.396 false 4.594,1.115 4.729,1.365 false 4.417,1.135 4.229,1.208 false 5.333,3.073 5.104,2.583 5.104,2.583 5.146,2.583 false 1.292,2.188 0.781,2.938 false 2.75,2.542 2.885,2.958 false 1.302,0.729 2.167,0.969 0.865,0.24 10 false Exhaust Gas 2.917,0.74 3.385,0.979 0.469,0.24 10 false ECM 0.365,2.979 1.24,3.479 0.875,0.5 10 false DPF Catalytic Converter 2.344,2.979 3.594,3.385 1.25,0.406 10 false Differential Pressure Sensor 3.854,0.094 5.708,0.365 1.854,0.271 10 false Property of Output Voltage: 4.76,1.292 5.677,1.51 0.917,0.219 10 false Stores P2455 5.156,2.51 6.125,2.74 0.969,0.229 10 false Stores P2454 4.052,0.615 6.188,0.885 2.135,0.271 10 false Differential Pressure Voltage (V) 4.021,0.958 4.396,1.125 0.375,0.167 10 false 5.000 3.865,1.146 4.24,1.313 0.375,0.167 10 false 4.800 3.865,1.344 4.24,1.51 0.375,0.167 10 false 4.650 4.021,2.375 4.396,2.542 0.375,0.167 10 false 1.530 4.021,2.594 4.396,2.76 0.375,0.167 10 false 0.750 4.021,2.75 4.396,2.917 0.375,0.167 10 false 0.555 4.021,2.896 4.396,3.063 0.375,0.167 10 false 0.400 4.292,3.146 4.396,3.302 0.104,0.156 10 false 0 4.771,3.24 4.875,3.396 0.104,0.156 10 false 0 4.531,3.24 4.708,3.406 0.177,0.167 10 false -5 4.938,3.24 5.229,3.406 0.292,0.167 10 false 20.0 6.469,3.24 6.854,3.406 0.385,0.167 10 false 100.0 4.323,3.469 6.885,3.708 2.563,0.24 10 false Exhaust Gas Differential Pressure (kPa)

The two sensing chambers of the differential pressure sensor assembly are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration. The sensor is a semiconductor-type that is not influenced by exhaust gases.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor assembly. If the difference between the pressure before and after the catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

HINT:

If the vacuum hoses of the differential pressure sensor assembly are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P2453 (Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance) is stored and the MIL illuminates.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2453 Diesel Particulate Filter Pressure Sensor "A" Circuit Range/Performance When the output voltage from the differential pressure sensor assembly indicates a reversal of positive and negative pressure.
(1 trip detection logic)
·

Incorrect differential pressure sensor assembly hose routing

·

Differential pressure sensor assembly vacuum hose is clogged

·

Blockage in vacuum transmitting pipe sub-assembly

·

Differential pressure sensor assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P2453 DPF Differential Pressure

HINT:
·

DTC P2454 (Diesel Particulate Filter Pressure Sensor "A" Circuit Low) and/or DTC P2455 (Diesel Particulate Filter Pressure Sensor "A" Circuit High) will be stored if there is an open or short malfunction in the differential pressure sensor assembly circuit.

·

After confirming DTC P2453, check the differential pressure in "Powertrain / Engine and ECT / Data List / DPF Differential Pressure" using the intelligent tester.


Reference:
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


CONFIRMATION DRIVING PATTERN

P2453
DTC Detection Drive Pattern Engine is running at 4000 rpm with no load for 10 seconds or more.

MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor assembly, the ECM always monitors the output voltage from the sensor. When the sensor output voltage is a reversal of positive and negative pressure, the ECM interprets this as an incorrect vacuum hose arrangement of the sensor, or determines that the vacuum hoses are clogged, and illuminates the MIL.

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2453)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs.

Result:
Result Proceed to
P2453 is output A
P2453 and other DTCs are output B



HINT:

If codes other than P2453 are output, perform troubleshooting for those DTCs first.



A

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)

B

GO TO DTC CHART

2.CHECK CONNECTION OF VACUUM HOSE (DIFFERENTIAL PRESSURE SENSOR - VACUUM TRANSMITTING PIPE)
a.

Check if the vacuum hose routing between the differential pressure sensor assembly and vacuum transmitting pipe is correct.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>INSTALLATION


b.

Check that there is no exhaust gas leakage between the differential pressure sensor assembly and vacuum transmitting pipe.


Result:
Proceed to
OK
NG



OK

3.CHECK BLOCKAGE OF VACUUM HOSE AND TRANSMITTING PIPE

NG

5.CORRECT TO NORMAL CONNECTION
3.CHECK BLOCKAGE OF VACUUM HOSE AND TRANSMITTING PIPE
CAUTION:

Be careful of being burned by exhaust gases during the following inspection.


a.

Disconnect the vacuum hoses (both upstream and downstream) from the differential pressure sensor assembly.


b.

Start the engine.


c.

Check if there are exhaust gas pulsations from both vacuum hoses during idling.

OK:

Exhaust gas pulsation exists.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING INTELLIGENT TESTER (DPF DIFFERENTIAL PRESSURE)

NG

6.REPLACE CLOGGED PARTS
4.READ VALUE USING INTELLIGENT TESTER (DPF DIFFERENTIAL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

d.

Check that the differential pressure is as specified below.

Result:
Condition Differential Pressure Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal



Result:
Proceed to
OK
NG



OK

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

7.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
5.CORRECT TO NORMAL CONNECTION
Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPLACE CLOGGED PARTS
Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPLACE DIFFERENTIAL PRESSURE SENSOR ASSEMBLY
a.

Replace the differential pressure sensor assembly.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>DIFFERENTIAL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off for 30 seconds or more.


e.

Turn the ignition switch to ON and turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

g.

Check that the differential pressure is as specified below.

HINT:
·

As long as the pipe connections are correct, the displayed pressure will not be vacuum pressure.

·

For reference result of real-vehicle check is as shown in the table below:

Condition DPF Differential Pressure
2500 rpm without load 0.5 kPa or more




h.

Start the engine.


i.

Engine is running at 4000 rpm with no load for 10 seconds or more.


j.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P2453.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, run the engine at 4000 rpm with no load for 10 seconds or more.



Result:
Proceed to
NEXT



NEXT

END