Home › Engine / Hybrid System › 2KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009568 2KD-FTV ENGINE CONTROL _0052068 ECD SYSTEM(for DPF) C

2KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P244B  Diesel Particulate Filter Differential Pressure Too High  


DESCRIPTION

Refer to DTC P244A (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P244A).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P244B Diesel Particulate Filter Differential Pressure Too High While driving, Catalyst Differential Pressure becomes more than 0.45 for 3 seconds.
(1 trip detection logic)
·

Front exhaust pipe assembly (DPF catalyst)

·

Differential pressure sensor assembly


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored

Related Data List
DTC No. Data List
P244B
·

DPF Differential Pressure

·

Catalyst Differential Press

·

Exhaust Fuel Addition FB



CONFIRMATION DRIVING PATTERN

P244B
DTC Detection Drive Pattern Engine is running at 4000 rpm with no load for 10 seconds or more.

MONITOR DESCRIPTION

The ECM compares pressure upstream and downstream of the DPF catalyst to monitor the differential pressure. If the differential pressure is large, the ECM determines that the DPF catalyst is contaminated or has deteriorated and illuminates the MIL.

A244057
2.125,3.49 2.344,3.49 false 2.344,3.49 2.729,2.031 true 4,1.323 4.521,0.594 true 4.521,0.594 4.698,0.594 false 5.844,2.583 5.302,2.219 false 5.844,2.583 5.979,2.583 false 1.229,3.417 2.125,3.656 0.896,0.24 10 false Stores P244B 3.531,2.979 3.99,3.208 0.458,0.229 10 false MAF 0.167,0.156 2.323,0.385 2.156,0.229 10 false Differential Pressure Malfunction: 0.25,1.604 1.219,2.115 0.969,0.51 10 false DPF Differential Pressure 4.771,0.521 5.969,0.75 1.198,0.229 10 false Clogged with PM 5.75,1.271 7.115,1.75 1.365,0.479 10 false Increases PM amount of DPF catalyst 6.042,2.479 6.969,2.979 0.927,0.5 10 false No PM in DPF catalyst 1.125,0.948 1.51,1.177 0.385,0.229 10 false High 5.604,2.958 5.99,3.188 0.385,0.229 10 false High 1.125,2.708 1.51,2.938 0.385,0.229 10 false Low 1.573,2.958 1.958,3.188 0.385,0.229 10 false Low

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ OUTPUT DTC (RECORD STORED DTC AND FREEZE FRAME DATA)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

d.

Record the stored DTC and freeze frame data.


e.

Check Exhaust Fuel Addition FB and Catalyst Differential Press in the freeze frame data.

HINT:
·

When the Exhaust Fuel Addition FB value is 1.41 or more, it indicates a high possibility of insufficient temperature increase during PM forced regeneration.

·

When the Catalyst Differential Press value is 0.45 or more, it indicates a high possibility that DPF catalyst is clogged.




Result:
Proceed to
NEXT



NEXT

2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
2.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P244B)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P244B is output A
P244B is output at the same time as P2463*
Other relevant DTCs are output B


HINT:

*: When P244B is output at the same time as P2463, perform this diagnostic procedure. When DTC P244B is not output at the same time as P2463 is output, perform the diagnostic procedure for P244C.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P244A




A

3.READ VALUE USING INTELLIGENT TESTER (DPF DIFFERENTIAL PRESSURE)

B

9.GO TO DTC CHART
3.READ VALUE USING INTELLIGENT TESTER (DPF DIFFERENTIAL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / DPF Differential Pressure.

Powertrain > Engine > Data List
Tester Display
DPF Differential Pressure
50003 61 238

d.

Check the DPF Differential Pressure values from idle speed to unloaded maximum engine speed.

Result:
Result Proceed to
DPF Differential Pressure increases as engine speed increases from idle speed A
Except above B


A241154
3.313,3.375 3.469,3.375 false 3.469,3.375 3.688,3.833 false 4.25,4.406 4.125,4.406 false 4.125,4.406 3.854,4.104 false 4.188,4.99 4.073,4.99 false 4.073,4.99 3.833,4.792 false 0.469,1.635 1.74,1.906 1.271,0.271 10 false Engine Speed (rpm) 0.844,3.031 1.635,3.271 0.792,0.24 10 false MAF (gm/s) 0.688,4.26 1.677,4.75 0.99,0.49 10 false DPF Differential Pressure (kPa) 4.208,4.896 4.333,5.042 0.125,0.146 10 false A 1.792,1.875 1.906,2.094 0.115,0.219 10 false 0 1.792,3.25 1.917,3.469 0.125,0.219 10 false 0 1.792,4.615 1.906,4.844 0.115,0.229 10 false 0 0.677,0.969 1.927,1.417 1.25,0.448 10 false Unloaded Maximum Engine Speed 2.385,3.292 3.344,3.531 0.958,0.24 10 false Normal Piping 4.313,4.323 5.271,4.563 0.958,0.24 10 false Clogged Piping 2.313,5.385 5.333,5.667 3.021,0.281 10 false Negative pressure occurs for approx. 1 second.

HINT:

If DPF Differential Pressure indicates negative pressure for approx. 1 second as shown in the illustration (A) when the engine speed increases, the differential pressure sensor piping of the DPF catalyst may be clogged.




A

5.CHECK FOR BLACK SMOKE

B

4.CLEAN OR REPLACE VACUUM TRANSMITTING HOSE
4.CLEAN OR REPLACE VACUUM TRANSMITTING HOSE
a.

Even though it has been determined that the vacuum transmitting hose needs to be repaired or cleaned, make sure to perform all diagnostic procedures for DTC P200C before repairing or cleaning it.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR BLACK SMOKE
5.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the above procedure [A] 10 times [B].


e.

Check for black smoke emission during procedures [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER (CATALYST DIFFERENTIAL PRESS)

NG

7.REPLACE FRONT EXHAUST PIPE ASSEMBLY
6.READ VALUE USING INTELLIGENT TESTER (CATALYST DIFFERENTIAL PRESS)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst Differential Press.

Powertrain > Engine > Data List
Tester Display
Catalyst Differential Press
50003 61 608

d.

Check the value of Catalyst Differential Press at 4000 rpm without load.

Result:
Result Proceed to
Catalyst Differential Press is more than 0.45 A
Except above B




A

7.REPLACE FRONT EXHAUST PIPE ASSEMBLY

B

8.PERFORM PM FORCED REGENERATION
7.REPLACE FRONT EXHAUST PIPE ASSEMBLY

Even though it has been determined that the front exhaust pipe assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P244B before replacing it.

Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
8.PERFORM PM FORCED REGENERATION
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION

Powertrain > Engine > Active Test
Tester Display
Activate the DPF Rejuvenate (PM)
50004 61 97
Result:

PM forced regeneration completes normally.



Result:
Proceed to
OK
NG



OK

END

NG

10.CHECK FUEL INJECTION SYSTEM
9.GO TO DTC CHART

Result:
Proceed to
NEXT



NEXT

10.CHECK FUEL INJECTION SYSTEM
10.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

11.CHECK INTAKE / EXHAUST SYSTEM
11.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

12.CHECK AFTER TREATMENT CONTROL SYSTEM
12.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

13.REPAIR OR REPLACE MALFUNCTIONING PARTS
13.REPAIR OR REPLACE MALFUNCTIONING PARTS
HINT:

Repair, replace or clean the following items only when it has been determined necessary based on diagnosis for DTC P244B.


a.

Clean and/or repair the hoses of the differential pressure sensor.


b.

Replace the front exhaust pipe assembly (DPF catalyst) .

Click hereEngine / Hybrid System>2KD-FTV INTAKE / EXHAUST>EXHAUST MANIFOLD W/ TURBOCHARGER(for DPF)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EMISSION CONTROL SYSTEM(w/ DPF)>ON-VEHICLE INSPECTION

Powertrain > Engine > Active Test
Tester Display
Activate the DPF Rejuvenate (PM)
50004 61 97

Result:
Proceed to
NEXT



NEXT

END