Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/ Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052076 SFI SYSTEM(w/ Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/ Secondary Air Injection System)  P0418  Secondary Air Injection System Control "A" Circuit  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>P0412).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0418 Secondary Air Injection System Control "A" Circuit Condition 1:

After cold engine starts, all of following conditions met (1 trip detection logic):

1.

Secondary air injection system not operating (air pump OFF, air switching valve OFF)

2.

Diagnostic signal from air injection control driver 20%

3.

Battery voltage 8 V or more



Condition 2:

After cold engine starts, all of following conditions met (1 trip detection logic):

1.

Secondary air injection system operating (air pump ON, air switching valve ON)

2.

Diagnostic signal from air injection control driver 20%

3.

Battery voltage 8 V or more



Condition 1:
·

Open in air pump drive circuit

·

Short between air pump drive circuit and +B circuit

·

Air pump assembly

·

Air injection control driver

·

ECM


Condition 2:
·

Short between air pump drive circuit and body ground

·

Air pump assembly

·

Air injection control driver

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the circuit containing the air pump of the secondary air injection system. The air injection control driver performs diagnosis of the air pump, air switching valve and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump, air switching valve or air injection control driver, it illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Air injection control driver
Required Sensors/Components (Related) Air pump assembly
Frequency of Operation Once per drive cycle

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds.

Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks.

While secondary air injection system operation using the intelligent tester is prohibited, the intelligent tester display indicates the prohibition (WAIT or ERROR).

If ERROR is displayed on the intelligent tester during the test, stop the engine for 10 minutes, and then try again.

·

Performing the Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If necessary, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the intelligent tester on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the intelligent tester on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the intelligent tester initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press the ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After the "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0418.

16.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the ignition switch off.


CAUTION / NOTICE / HINT

CAUTION:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR INJECTION CONTROL DRIVER - BODY GROUND)
a.

Disconnect the air pump connector.


b.

Disconnect the air injection control driver.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 - A34-2 (VP) Always Below 1 Ω
Positive (+) battery cable terminal - A34-1 (BATT) Always Below 1 Ω
A33-1 - Body ground Always Below 1 Ω
A33-2 or A34-2 (VP) - Body ground Always 10 kΩ or higher
Positive (+) battery cable terminal or A34-1 (BATT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT AIR PUMP ASSEMBLY

OK

NG

3.REPLACE AIR PUMP ASSEMBLY
3.REPLACE AIR PUMP ASSEMBLY

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM(w/ Secondary Air Injection System)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

g.

Turn the ignition switch off and wait for at least 30 seconds.


h.

Turn the ignition switch to ON and turn the intelligent tester on.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

Powertrain > Engine > Utility
Tester Display
Secondary Air Injection Check
50005 61 26

j.

Start the engine after the intelligent tester initialization is finished.


k.

Perform the System Check operation by pressing Next.


l.

After operating the secondary air injection system, perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


m.

Read pending DTCs.

Powertrain > Engine > Trouble Codes
50001 61
OK:

No pending DTC is output.



n.

Turn the engine switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.




Result:
Proceed to
OK
NG



OK

END

NG