Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) J

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the starter (ST) relay drive signal output from the ignition switch is input into the STA terminal of the ECM, and the NE signal generated by the crankshaft position sensor is input into the NE+ terminal. The ECM determines that the engine is cranked, and turns transistor in the ECM internal circuit on. Current flows to the circuit opening (C/OPN) relay by turning transistor on.

Then, the fuel pump operates.

While the NE signal is input into the ECM and the engine is running, the ECM turns transistor on continuously.

WIRING DIAGRAM

A247785
5.938,4.094 6.26,4.333 0.323,0.24 10 false FC 5.948,2.302 6.542,2.615 0.594,0.313 10 false MREL 6.26,4.75 6.76,4.99 0.5,0.24 10 false ECM 0.656,3.781 1.427,4.052 0.771,0.271 10 false Fuel Pump 3.073,3.958 3.635,4.146 0.563,0.188 10 false C/OPN 3.802,0.688 4.302,0.958 0.5,0.271 10 false IGN 1.781,1.031 2.823,1.323 1.042,0.292 10 false Ignition Switch 2.469,0.646 2.823,0.865 0.354,0.219 10 false IG2 1.771,0.646 2.188,0.875 0.417,0.229 10 false AM2 1.781,0.885 2.083,1.104 0.302,0.219 10 false G9 0.542,1.229 0.927,1.438 0.385,0.208 10 false AM2 2.969,2.083 3.344,2.313 0.375,0.229 10 false EFI 3.646,2.625 4.146,2.833 0.5,0.208 10 false MAIN 1.021,2.094 1.813,2.365 0.792,0.271 10 false BATT P/I 0.688,4.604 1.302,5.01 0.615,0.406 10 false Battery 5.677,4.094 5.948,4.344 0.271,0.25 10 false 25 5.75,2.219 5.865,2.375 0.115,0.156 10 false 8 6.26,4.604 6.667,4.802 0.406,0.198 10 false G89 1.615,0.469 1.729,0.615 0.115,0.146 10 false 5 2.792,0.469 2.906,0.615 0.115,0.146 10 false 6 4.688,2.313 5.042,2.646 0.354,0.333 10 false 1J 2.375,2.313 2.698,2.552 0.323,0.24 10 false 1J 2.375,1.948 2.698,2.208 0.323,0.26 10 false 1H 2.427,1.771 2.552,1.927 0.125,0.156 10 false 1 4.729,2.135 4.844,2.302 0.115,0.167 10 false 2 2.427,2.146 2.542,2.313 0.115,0.167 10 false 3 2.385,3.219 2.688,3.479 0.302,0.26 10 false 1J 2.427,3.021 2.542,3.188 0.115,0.167 10 false 8 4.688,3.635 4.969,3.833 0.281,0.198 10 false 1J 4.719,3.458 4.833,3.625 0.115,0.167 10 false 6 4.688,4.177 4.969,4.385 0.281,0.208 10 false 1J 4.719,4 4.833,4.167 0.115,0.167 10 false 7 0.656,3.635 0.99,3.896 0.333,0.26 10 false L4 1.781,3.365 1.906,3.521 0.125,0.156 10 false 4 1.781,4.177 1.906,4.333 0.125,0.156 10 false 5 2.885,4.688 4.49,4.99 1.604,0.302 10 false No. 1 Integration Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5

d.

Check whether the fuel pump operating sound occurs when performing the Active Test on the intelligent tester.

OK:

Fuel pump operating sound occurs.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

NG

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

d.

Check the result when the ignition switch is turned to ON and START.

OK:
Ignition Switch Position Starter Signal
ON Close (Starter signal OFF)
START Open (Starter signal ON)



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)

NG

REPAIR OR REPLACE STARTING SYSTEM

3.READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the intelligent tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315

d.

Read the values displayed on the intelligent tester while cranking the engine.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CRANKSHAFT POSITION SENSOR CIRCUIT

4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G89-25 (FC) - 1J-7 Always Below 1 Ω
G89-25 (FC) or 1J-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT NO. 1 INTEGRATION RELAY (C/OPN RELAY INPUT VOLTAGE)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block.


b.
A112973
1.281,0.385 1.625,0.604 0.344,0.219 0.073,0.083 0.479,0.271 0.406,0.188 10 false *a 1.375,0.427 1.781,0.615 0.406,0.188 10 false 1J
*a Component with harness connected
(No. 1 Integration Relay)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
1J-6 - Body ground Ignition switch off Below 1 V
1J-8 - Body ground
1J-6 - Body ground Ignition switch ON 11 to 14 V
1J-8 - Body ground Engine cranking



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP - BODY GROUND)

NG

8.INSPECT NO. 1 INTEGRATION RELAY (C/OPN)
6.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - FUEL PUMP - BODY GROUND)
a.

Check the harness and connectors between the No. 1 integration relay and fuel pump.

i.

Remove the No. 1 integration relay from the engine room relay block and junction block.


ii.

Disconnect the fuel pump connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-4 - 1J-8 Always Below 1 Ω
L4-4 or 1J-8 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the fuel pump and body ground.

i.

Disconnect the fuel pump connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-5 - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

NG

8.INSPECT NO. 1 INTEGRATION RELAY (C/OPN)
a.

Inspect the No. 1 integration relay (C/OPN).

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - NO. 1 INTEGRATION RELAY)

NG

REPLACE NO. 1 INTEGRATION RELAY

9.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH - NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-6 (IG2) - 1J-6 Always Below 1 Ω
G9-6 (IG2) or 1J-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR