Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) J

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  ECM Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, the battery voltage is applied to the IGSW terminal of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the No. 1 integration relay (MAIN relay), closing the contacts and supplying power to terminals +B of the ECM.

WIRING DIAGRAM

A247782
5.479,0.646 5.948,0.917 0.469,0.271 10 false G89 5.479,1.979 5.906,2.219 0.427,0.24 10 false G89 5.479,2.396 5.865,2.656 0.385,0.26 10 false G89 5.49,2.927 5.813,3.135 0.323,0.208 10 false C75 5.573,0.448 5.698,0.604 0.125,0.156 10 false 9 5.573,2.74 5.688,2.896 0.115,0.156 10 false 3 5.844,0.521 6.323,0.708 0.479,0.188 10 false IGSW 5.844,1.969 6.198,2.198 0.354,0.229 10 false +B 5.844,2.396 6.365,2.656 0.521,0.26 10 false MREL 5.844,2.927 6.135,3.094 0.292,0.167 10 false E1 2.448,2.104 2.896,2.323 0.448,0.219 10 false EFI 3.594,2.708 4.094,2.927 0.5,0.219 10 false MAIN 4.323,1.969 4.719,2.208 0.396,0.24 10 false 1J 4.333,2.396 4.667,2.677 0.333,0.281 10 false 1J 1.677,2.406 2.042,2.708 0.365,0.302 10 false 1J 1.667,1.979 2.063,2.229 0.396,0.25 10 false 1H 1.708,1.771 1.813,1.938 0.104,0.167 10 false 1 2.365,0.531 2.469,0.698 0.104,0.167 10 false 5 3.667,0.531 3.771,0.698 0.104,0.167 10 false 6 4.365,2.208 4.469,2.375 0.104,0.167 10 false 2 1.708,2.208 1.813,2.375 0.104,0.167 10 false 3 4.365,1.76 4.469,1.927 0.104,0.167 10 false 4 1.188,0.781 1.635,1.042 0.448,0.26 10 false AM2 2.552,0.729 2.99,1.031 0.438,0.302 10 false AM2 2.375,3.135 3.927,3.396 1.552,0.26 10 false No. 1 Integration Relay 0.51,3.125 1.115,3.396 0.604,0.271 10 false Battery 0.573,2.135 1.323,2.354 0.75,0.219 10 false BATT P/I 6.198,3.333 6.667,3.573 0.469,0.24 10 false ECM 4.51,0.781 4.917,0.979 0.406,0.198 10 false IGN 5.573,1.792 5.688,1.948 0.115,0.156 10 false 1 5.573,2.219 5.688,2.375 0.115,0.156 10 false 8 3.281,0.729 3.667,0.948 0.385,0.219 10 false IG2 2.583,1.01 2.917,1.292 0.333,0.281 10 false G9 2.583,1.167 3.698,1.479 1.115,0.313 10 false Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK NO. 1 INTEGRATION RELAY (POWER SOURCE)
a.
A201293
0.667,1.021 1.042,1.26 0.375,0.24 0.094,0.073 0.521,0.354 0.427,0.281 10 false *a 0.771,1.063 1.198,1.344 0.427,0.281 10 false 1H
*a Front view of wire harness connector
(to No. 1 Integration Relay)


Remove the No. 1 integration relay from the engine room relay block and junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1H-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT NO. 1 INTEGRATION RELAY (MAIN)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - BATTERY)

2.INSPECT NO. 1 INTEGRATION RELAY (MAIN)
a.

Inspect the No. 1 integration relay (MAIN).

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, BODY GROUND)

NG

REPLACE NO. 1 INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM, BODY GROUND)
a.

Check the harness and connectors between the No. 1 integration relay and ECM.

i.

Remove the No. 1 integration relay from the engine room relay block and junction block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G89-8 (MREL) - 1J-2 Always Below 1 Ω
G89-1 (+B) - 1J-4 Always Below 1 Ω
G89-8 (MREL) or 1J-2 - Body ground Always 10 kΩ or higher
G89-1 (+B) or 1J-4 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the No. 1 integration relay and body ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1J-3 - Body ground Always Below 1 Ω




Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C75-3 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
a.
A247783
0.635,1.01 0.948,1.24 0.313,0.229 2.49,1.01 2.802,1.24 0.313,0.229 2.271,2.854 2.802,2.188 true 1.146,2.677 0.865,2.104 true 0.073,0.052 0.458,0.281 0.385,0.229 10 false *a 0.677,1.052 1.063,1.281 0.385,0.229 10 false C75 2.521,1.052 2.906,1.281 0.385,0.229 10 false G89 1.115,2.708 1.854,2.979 0.74,0.271 10 false 3 (E1) 2.229,2.875 2.969,3.146 0.74,0.271 10 false 9 (IGSW)
*a Rear view of wire harness connector
(to ECM)


Disconnect the ECM connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G89-9 (IGSW) - C75-3 (E1) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

6.CHECK HARNESS AND CONNECTOR (ECM - IGNITION SWITCH ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (ECM - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-6 (IG2) - G89-9 (IGSW) Always Below 1 Ω
G9-6 (IG2) or G89-9 (IGSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>2TR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMBLY