Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0100  Mass Air Flow Circuit Malfunction  P0102  Mass Air Flow Circuit Low  P0103  Mass Air Flow Circuit High  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When either of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.


A122492
1.417,0.5 1.917,1.5 true 2.625,1.063 2.281,1.49 true 4.698,1.271 4.073,2.167 true 5.021,1.552 5.51,2.198 true 0.115,0.302 1.375,0.719 1.26,0.417 10 false Temperature Sensor (Thermistor) 2.167,0.146 2.448,0.365 0.281,0.219 10 false B+ 2.208,0.542 3.573,0.781 1.365,0.24 10 false Power Transistor 2.667,0.958 4.406,1.229 1.74,0.271 10 false Platinum Hot Wire (Heater) 1.667,1.49 1.833,1.698 0.167,0.208 10 false A 2.469,1.49 2.656,1.688 0.188,0.198 10 false B 2.896,1.573 3.938,1.823 1.042,0.25 10 false Output Voltage 5.167,2.188 6.979,2.385 1.813,0.198 10 false Platinum Hot Wire (Heater) 2.896,2.188 5.417,2.396 2.521,0.208 10 false Temperature Sensor (Thermistor)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass Air Flow Circuit Malfunction Mass air flow meter circuit is open or shorted for more than 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0102 Mass Air Flow Circuit Low Mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass Air Flow Circuit High Mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

When either of these DTCs is stored, check the air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

MAF (gm/s) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Turn the ignition switch to ON and wait for 5 seconds or more.


WIRING DIAGRAM

A247764
0.563,2.688 1.198,2.938 0.635,0.25 10 false Battery 0.396,1.958 1.198,2.229 0.802,0.271 10 false BATT P/I 1.063,0.615 1.396,0.833 0.333,0.219 10 false 1H 1.104,0.417 1.219,0.604 0.115,0.188 10 false 1 2.917,0.615 3.198,0.792 0.281,0.177 10 false 1J 2.958,0.427 3.073,0.615 0.115,0.188 10 false 5 2.906,0.99 3.188,1.198 0.281,0.208 10 false 1J 2.948,0.802 3.063,0.99 0.115,0.188 10 false 2 1.698,1.406 2.01,1.656 0.313,0.25 10 false 1J 1.469,1.385 1.583,1.573 0.115,0.188 10 false 3 2.198,1.354 2.646,1.542 0.448,0.188 10 false MAIN 1.604,0.771 1.958,0.969 0.354,0.198 10 false EFI 1.875,1.615 3.354,1.917 1.479,0.302 10 false No. 1 Integration Relay 3.5,0.49 3.635,0.667 0.135,0.177 10 false 1 4.979,0.833 5.115,1.01 0.135,0.177 10 false 3 4.979,1.375 5.115,1.552 0.135,0.177 10 false 2 3.656,0.479 4,0.729 0.344,0.25 10 false +B 4.677,0.844 5.063,1.083 0.385,0.24 10 false VG 5.729,0.844 6.135,1.115 0.406,0.271 10 false VG 4.594,1.396 4.969,1.708 0.375,0.313 10 false E2G 5.719,1.375 6.125,1.625 0.406,0.25 10 false E2G 3.635,1.917 4.063,2.115 0.427,0.198 10 false C36 3.635,2.073 5.135,2.406 1.5,0.333 10 false Mass Air Flow Meter 6.177,3.25 6.51,3.417 0.333,0.167 10 false ECM 5.396,0.76 5.698,0.958 0.302,0.198 10 false 28 5.396,1.313 5.698,1.531 0.302,0.219 10 false 30 5.354,0.958 5.729,1.156 0.375,0.198 10 false C76 5.354,1.5 5.719,1.74 0.365,0.24 10 false C76 5.354,2.865 5.635,3.031 0.281,0.167 10 false G89 5.438,2.667 5.552,2.844 0.115,0.177 10 false 8 5.708,2.771 6.219,3 0.51,0.229 10 false MREL

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (MAF)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

Powertrain > Engine > Data List
Tester Display
MAF
50003 61 319

e.

Read the values displayed on the intelligent tester.

Result:
MAF (gm/s) Proceed to
Approximately 0.0 A
160.0 or more B
Between 1.0 and 160.0* C


HINT:

*: The value must change when the throttle valve is opened or closed with the engine running.




A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

C

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
a.
A107942
0.583,1.052 0.958,1.281 0.375,0.229 1.208,1.896 1.406,1.51 false 0,0 0.313,0.156 0.313,0.156 10 false *a 0.646,1.094 1.042,1.385 0.396,0.292 10 false C36 1,1.833 1.365,2.063 0.365,0.229 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-3 (VG) - C76-28 (VG) Always Below 1 Ω
C36-2 (E2G) - C76-30 (E2G) Always Below 1 Ω
C36-3 (VG) or C76-28 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER

Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-1 (+B) - 1J-5 Always Below 1 Ω
C36-1 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-3 (VG) - C76-28 (VG) Always Below 1 Ω
C36-2 (E2G) - C76-30 (E2G) Always Below 1 Ω
C36-3 (VG) or C76-28 (VG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-2 (E2G) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG