Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM(w/o Secondary Air Injection System) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009569 2TR-FE ENGINE CONTROL _0052091 SFI SYSTEM(w/o Secondary Air Injection System) C

2TR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Deviation in the crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (bank 1)

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


- DTC stored

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0016.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Required Sensors/Components (Related) Camshaft position sensor, Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A197314E57
4.25,1.115 4.594,0.49 4.594,0.49 4.74,0.49 false 0.156,0.656 1.135,0.885 0.979,0.229 10 false Vehicle Speed 1.51,2.146 1.813,2.385 0.302,0.24 10 false [A] 2.167,1.635 2.479,1.854 0.313,0.219 10 false [B] 3.188,1.646 3.479,1.854 0.292,0.208 10 false [C] 3.823,3.021 4.104,3.281 0.281,0.26 10 false [D] 4.677,0.875 4.969,1.115 0.292,0.24 10 false [E] 5.656,1.646 5.927,1.917 0.271,0.271 10 false [F] 6.365,3.021 6.688,3.281 0.323,0.26 10 false [G] 0.719,1.771 1.167,2.063 0.448,0.292 10 false Idling 4.813,0.333 6.24,0.792 1.427,0.458 10 false There is no designated vehicle speed 0.167,2.052 1.104,2.469 0.938,0.417 10 false Ignition Switch ON 1.927,2.531 2.708,2.969 0.781,0.438 10 false Warming up the engine 2.74,2.552 4,2.781 1.26,0.229 10 false 5 minutes or more 5.271,2.531 6.427,2.698 1.156,0.167 10 false 5 minutes or more 4.125,2.563 5.021,2.729 0.896,0.167 10 false 2 to 3 minutes

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the intelligent tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the intelligent tester on [A].

6.

Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0016.

12.

Check the DTC judgment result.

Intelligent Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine and ECT / DTC [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0016 is output A
P0016 and other DTCs are output B


HINT:

If any DTCs other than P0016 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the intelligent tester on.


d.

Warm up the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / All Data / VVT Change Angle #1.

Powertrain > Engine > Active Test
Active Test Display
Control the VVT Linear (Bank1)
Data List Display
VVT Change Angle #1
50004 61 32 203

f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.ADJUST VALVE TIMING

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.ADJUST VALVE TIMING

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.INSPECT OIL CONTROL VALVE FILTER
a.

Remove the oil control valve filter.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY


b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY
a.

Replace the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2TR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

e.

Start the engine and warm it up.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Read the output pending DTCs using the intelligent tester.

Powertrain > Engine > Trouble Codes
50001 61
OK:

No pending DTC is output.



Result:
Proceed to
OK
NG



OK

END

NG