Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(w/o EGR Cooler) › 2011.10–2012.04
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052103 ECD SYSTEM(w/o EGR Cooler) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(w/o EGR Cooler)  P0047  Turbocharger/Supercharger Boost Control "A" Circuit Low  P0048  Turbocharger/Supercharger Boost Control "A" Circuit High  


DESCRIPTION

Refer to DTC P0046 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>P0046).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low Both of following conditions met for 1 second or more
(1 trip detection logic):
·

DC motor duty ratio 100%

·

DC motor current 0.5 A or less


·

Open in DC motor circuit

·

Turbo motor driver

·

DC Motor (turbocharger sub-assembly)


Comes on DTC stored
P0048 Turbocharger/Supercharger Boost Control "A" Circuit High DC motor current 6.5 A or more for 0.5 seconds or more
(1 trip detection logic)
·

Short in DC motor circuit

·

Turbo motor driver

·

DC Motor (turbocharger sub-assembly)


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

P0047, P0048
DTC Detection Drive Pattern Drive the vehicle with a city driving pattern at least 10 minutes.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
a.

Turn the ignition switch to ON.


b.

Turn the ignition switch off and check the DC motor operation (check the operation link movement).

HINT:

When it is necessary to repeat this inspection, wait 30 seconds or more with the ignition switch off before performing the inspection.


OK:

When the ignition switch is turned off, the operation link moves as shown in A to D in the illustration below and the operation link contacts the stopper bolt


A158317
5.479,1.969 6.031,1.948 false 5.531,1.615 5.969,1.531 false 5.615,1.167 6.083,1.115 false 4.75,4.125 5.625,3.375 false 6.146,1.031 7.094,1.198 0.948,0.167 10 false Operation Link 6.052,1.448 6.688,1.646 0.635,0.198 10 false Lock Nut 6.083,1.875 6.917,2.073 0.833,0.198 10 false Stopper Bolt 5.677,3.271 7.031,3.479 1.354,0.208 10 false Stopper Bolt Contact 2.521,4.333 4.594,4.552 2.073,0.219 10 false Ignition Switch off Time (sec.) 0.427,1.896 1.573,2.25 1.146,0.354 10 false Motor Rod Stroke (mm (in.)) 1.938,0.302 2.135,0.469 0.198,0.167 10 false A 3.177,0.302 3.375,0.469 0.198,0.167 10 false B 4.531,0.302 4.729,0.469 0.198,0.167 10 false C 5.406,0.302 5.604,0.469 0.198,0.167 10 false D 0.156,4.813 1.115,5.031 0.958,0.219 10 false Ignition Switch 1.552,4.99 1.885,5.208 0.333,0.219 10 false off 1.219,4.646 1.552,4.865 0.333,0.219 10 false ON


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR)
2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR)
a.
C217215
2.021,1.219 2.479,0.792 2.479,0.792 2.552,0.792 true 1.396,1.26 0.948,0.833 0.948,0.833 0.875,0.833 true 0.125,0.156 0.302,0.333 0.177,0.177 10 false *a 2.604,0.719 3.01,1.031 0.406,0.313 10 false M- 0.615,0.74 1.063,1.021 0.448,0.281 10 false M+
*a Component without harness connected
(DC Motor)


Disconnect the DC motor connector.


b.

Measure the DC motor resistance.

Standard resistance:

1 to 100 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

NG

6.REPLACE TURBOCHARGER SUB-ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)
a.

Disconnect the DC motor connector.


b.

Disconnect the turbo motor driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C39-12 (M+) - C41-2 (M+) Always Below 1 Ω
C39-5 (M-) - C41-1 (M-) Always Below 1 Ω
C39-12 (M+) or C41-2 (M+) - Body ground Always 10 kΩ or higher
C39-5 (M-) or C41-1 (M-) - Body ground Always 10 kΩ or higher



d.

Reconnect the turbo motor driver connector.


e.

Reconnect the DC motor connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE TURBO MOTOR DRIVER

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE TURBO MOTOR DRIVER

Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0047 AND/OR P0048)
5.CHECK WHETHER DTC OUTPUT RECURS (DTC P0047 AND/OR P0048)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.


f.

Turn the ignition switch to ON and wait for 10 seconds or more.


g.

Start the engine.


h.

Drive the vehicle with a city driving pattern at least 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Read the DTCs.

Result:
Result Proceed to
P0047 and/or P0048 is output A
No DTC is output B




A

6.REPLACE TURBOCHARGER SUB-ASSEMBLY

B

END

6.REPLACE TURBOCHARGER SUB-ASSEMBLY

Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off.


e.

Remove the EFI fuse from the engine room relay block and junction block assembly for more than 1 minute.


f.

Turn the ignition switch to ON and wait for 10 seconds or more.


g.

Start the engine.


h.

Drive the vehicle with a city driving pattern at least 10 minutes.


i.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

j.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END