Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0031  Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1)  P0032  Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).

·

This DTC is related to the air fuel ratio sensor, although the caption is the oxygen sensor.



The air fuel ratio sensor outputs a voltage* that is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage is used to control the A/F mixture.

The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engine. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and particulate matter (PM).

In order to reduce PM, the ECM adjusts the air-fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.

When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.

*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The intelligent tester can be used to monitor this voltage.

A258975
5.24,2.021 5.771,2.531 true 5.021,1.802 5.688,1.99 true 5.167,1.396 5.677,1.344 true 5.396,1.292 5.719,1.115 true 5.177,1.729 5.688,1.979 true 3.208,2.281 3.854,1.938 false 3.031,2.219 2.302,1.854 true 2.583,2.625 2.708,2.823 0.125,0.198 10 false A 3.271,2.625 3.396,2.802 0.125,0.177 10 false A 1.76,1.75 2.427,1.979 0.667,0.229 10 false Element 0.677,2.083 1.552,2.302 0.875,0.219 10 false Exhaust Gas 4.875,2.677 5.802,2.938 0.927,0.26 10 false A-A Section 5.719,1.917 7.146,2.198 1.427,0.281 10 false Platinum Electrode 3.906,1.875 4.417,2.135 0.51,0.26 10 false Cover 5.823,2.479 6.115,2.677 0.292,0.198 10 false Air 5.76,0.969 6.219,1.146 0.458,0.177 10 false Heater 5.729,1.219 6.854,1.646 1.125,0.427 10 false Solid Electrolyte (Zirconia Element) 0.406,4.792 1.552,5 1.146,0.208 10 false AF Lambda B1S1 0.375,6.115 1.604,6.313 1.229,0.198 10 false AFS Voltage B1S1 2.031,4.875 2.198,5.083 0.167,0.208 10 false 1 2.031,4.354 2.198,4.563 0.167,0.208 10 false 2 2.042,6.24 2.208,6.448 0.167,0.208 10 false 1 2.042,6.781 2.208,6.99 0.167,0.208 10 false 0 2.031,5.406 2.198,5.615 0.167,0.208 10 false 0 2.042,5.719 2.208,5.927 0.167,0.208 10 false 2 2.302,5.698 2.531,5.948 0.229,0.25 10 false (V) 2.927,6.979 3.177,7.229 0.25,0.25 10 false 10 3.24,7.073 3.594,7.323 0.354,0.25 10 false 14.5 3.688,6.979 3.938,7.229 0.25,0.25 10 false 20 4.458,6.979 4.708,7.229 0.25,0.25 10 false 30 5.229,6.979 5.479,7.229 0.25,0.25 10 false 40 5.99,6.979 6.24,7.229 0.25,0.25 10 false 50 0.156,3.354 2.458,3.635 2.302,0.281 10 false Air-Fuel Ratio Displayed on Tester: 3.688,7.292 4.625,7.49 0.938,0.198 10 false Air-Fuel Ratio 4.104,4.99 6.729,5.323 2.625,0.333 10 false AF Lambda B1S1 = Air-Fuel Ratio / 14.5 2.604,8.281 3.021,8.469 0.417,0.188 10 false 0.060 4.833,8.281 5.25,8.469 0.417,0.188 10 false 0.508 5.406,8.281 5.823,8.469 0.417,0.188 10 false 0.787 5.958,8.281 6.375,8.469 0.417,0.188 10 false 0.978 6.51,8.281 6.927,8.469 0.417,0.188 10 false 1.373 4.281,8.281 4.698,8.469 0.417,0.188 10 false 0.336 3.729,8.281 4.146,8.469 0.417,0.188 10 false 0.268 3.167,8.281 3.583,8.469 0.417,0.188 10 false 0.170 2.188,8.281 2.375,8.469 0.188,0.188 10 false 0 2.115,8.729 2.448,8.917 0.333,0.188 10 false 14.5 6.031,8.729 6.365,8.917 0.333,0.188 10 false 30 2.688,8.729 3.021,8.917 0.333,0.188 10 false 15 4.906,8.729 5.24,8.917 0.333,0.188 10 false 20 6.615,8.729 6.948,8.917 0.333,0.188 10 false 50 3.802,8.729 4.135,8.917 0.333,0.188 10 false 17 3.229,8.729 3.563,8.917 0.333,0.188 10 false 16 0.375,8.729 1.313,8.927 0.938,0.198 10 false Air-Fuel Ratio 4.344,8.729 4.677,8.917 0.333,0.188 10 false 18 5.479,8.729 5.813,8.917 0.333,0.188 10 false 25 1.146,8.219 1.375,8.469 0.229,0.25 10 false (V) 0.323,8.146 1.115,8.521 0.792,0.375 10 false AFS Voltage B1S1 0.333,7.615 1.135,8 0.802,0.385 10 false AF Lambda B1S1 2.146,7.771 2.375,7.938 0.229,0.167 10 false 1.0 2.625,7.771 2.969,7.948 0.344,0.177 10 false 1.03 3.177,7.771 3.49,7.969 0.313,0.198 10 false 1.10 3.719,7.771 4.031,7.917 0.313,0.146 10 false 1.17 4.302,7.771 4.594,7.969 0.292,0.198 10 false 1.24 4.833,7.771 5.146,7.917 0.313,0.146 10 false 1.38 5.417,7.771 5.75,7.927 0.333,0.156 10 false 1.72 5.969,7.771 6.26,7.917 0.292,0.146 10 false 2.07 6.563,7.771 6.885,7.927 0.323,0.156 10 false 3.45 0.396,9.156 0.792,9.344 0.396,0.188 10 false HINT: 0.667,9.427 6.219,9.698 5.552,0.271 10 false *1: AFS Voltage B1S1 cannot be displayed correctly when the value is 0 V or less. 1.5,8.292 1.948,8.479 0.448,0.188 10 false -0.549 1.583,8.729 1.917,8.917 0.333,0.188 10 false 12 1.542,7.781 1.854,7.948 0.313,0.167 10 false 0.83 1.438,8.063 1.635,8.25 0.198,0.188 10 false *1 2.042,3.875 2.208,4.083 0.167,0.208 10 false 3

HINT:

The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the B+ side of the circuit.


A210271
3.531,0.813 3.656,0.969 3.656,0.969 3.854,0.969 false 3.583,1.281 3.667,1.375 3.667,1.375 3.865,1.375 false 0.135,0.083 0.875,0.344 0.74,0.26 10 false Reference: 0.083,0.635 0.563,1.052 0.479,0.417 10 false from Battery 1.563,0.281 2.365,0.51 0.802,0.229 10 false A/F Relay 2.813,0.281 4.281,0.573 1.469,0.292 10 false Air Fuel Ratio Sensor 0.75,0.865 1.521,1.198 0.771,0.333 10 false A/F Fuse 3.906,0.875 4.375,1.073 0.469,0.198 10 false Heater 3.906,1.292 4.385,1.49 0.479,0.198 10 false Sensor 5.594,0.24 6,0.479 0.406,0.24 10 false ECM 4.896,0.646 5.292,0.844 0.396,0.198 10 false HAF2 4.896,1.063 5.313,1.229 0.417,0.167 10 false AF2+ 4.896,1.49 5.292,1.708 0.396,0.219 10 false AF2- 6.083,1.219 6.531,1.698 0.448,0.479 10 false Duty Control 0.885,1.688 2.24,1.979 1.354,0.292 10 false from MAIN Relay

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 4 seconds.
(1 trip detection logic)
·

Open in air fuel ratio sensor heater circuit

·

air fuel ratio sensor heater

·

A/F relay

·

ECM


Comes on DTC stored
P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) Air fuel ratio sensor heater current is 0.8 A or more when the heater does not operate for 4 seconds.
(1 trip detection logic)
·

Short in air fuel ratio sensor heater circuit

·

Air fuel ratio sensor heater

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0031
·

AFS Voltage B1S1

·

AF Lambda B1S1

·

Exhaust Temperature B1S1


P0032

CONFIRMATION DRIVING PATTERN

P0031
DTC Detection Drive Pattern
·

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

·

Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the intelligent tester.



P0032
DTC Detection Drive Pattern Ignition switch ON for 5 seconds

MONITOR DESCRIPTION

The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air-fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.

WIRING DIAGRAM

A276463
3.396,1.719 4.76,1.917 1.365,0.198 10 false Air Fuel Ratio Sensor 5.323,2.865 5.75,3.073 0.427,0.208 10 false G148 5.333,2.031 5.698,2.24 0.365,0.208 10 false C111 5.719,0.469 6.167,0.698 0.448,0.229 10 false HAF2 5.719,1.26 6.104,1.469 0.385,0.208 10 false AF2+ 5.729,1.938 6.104,2.146 0.375,0.208 10 false AF2- 5.719,2.854 6.167,3.052 0.448,0.198 10 false MREL 5.438,2.688 5.635,2.854 0.198,0.167 10 false 11 5.5,1.875 5.656,2.073 0.156,0.198 10 false 1 5.5,1.177 5.688,1.406 0.188,0.229 10 false 2 5.49,0.406 5.688,0.604 0.198,0.198 10 false 6 3.781,0.469 4.063,0.667 0.281,0.198 10 false +B 4.219,1.198 4.646,1.417 0.427,0.219 10 false AF2+ 3.76,1.188 4.135,1.458 0.375,0.271 10 false AF2- 4.969,2.417 5.542,2.646 0.573,0.229 10 false Shielded 1.125,2.719 1.396,2.896 0.271,0.177 10 false EFI 1.771,3.177 2.198,3.354 0.427,0.177 10 false MAIN 6.135,4.792 6.656,5.083 0.521,0.292 10 false ECM 1.031,3.802 2.625,4.031 1.594,0.229 10 false No. 1 Integration Relay 0.938,4.313 1.615,4.615 0.677,0.302 10 false BATT P/I 1.073,4.958 1.781,5.219 0.708,0.26 10 false Battery 0.771,3.625 1.031,3.802 0.26,0.177 10 false 1H 0.615,3.615 0.76,3.813 0.146,0.198 10 false 1 2.573,3.458 2.813,3.635 0.24,0.177 10 false 1J 2.615,2.865 2.854,3.031 0.24,0.167 10 false 1J 2.677,2.656 2.875,2.865 0.198,0.208 10 false 2 2.625,3.292 2.729,3.469 0.104,0.177 10 false 3 3.396,1.583 3.792,1.802 0.396,0.219 10 false C124 5.333,1.344 5.729,1.531 0.396,0.188 10 false C111 5.323,0.573 5.792,0.823 0.469,0.25 10 false C111 4.198,0.458 4.583,0.708 0.385,0.25 10 false HAF2 3.594,0.469 3.802,0.719 0.208,0.25 10 false 2 4.625,0.458 4.781,0.698 0.156,0.24 10 false 1 3.594,1.24 3.781,1.427 0.188,0.188 10 false 4 4.635,1.219 4.802,1.417 0.167,0.198 10 false 3 0.594,0.719 0.917,0.979 0.323,0.26 10 false A/F 2.51,2.146 2.781,2.344 0.271,0.198 10 false 1J 2.333,2.146 2.531,2.354 0.198,0.208 10 false 5 1.813,1.177 2.125,1.448 0.313,0.271 10 false A/F 1.49,0.938 1.646,1.146 0.156,0.208 10 false 2 2.271,0.948 2.448,1.156 0.177,0.208 10 false 1 1.5,0.469 1.698,0.708 0.198,0.24 10 false 5 2.281,0.479 2.458,0.708 0.177,0.229 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)

NG

5.REPLACE AIR FUEL RATIO SENSOR
2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR HEATER VOLTAGE)
a.
A122781
0.552,1 0.99,1.292 0.438,0.292 1.927,1.042 2.198,0.865 false 0.24,0.125 0.438,0.281 0.198,0.156 10 *a 2.25,0.74 2.469,0.896 0.219,0.156 10 +B 0.604,1.063 1.031,1.26 0.427,0.198 10 C124
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


Disconnect the air fuel ratio sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C124-2 (+B) - Body ground Ignition switch ON 11 to 14 V



d.

Reconnect the air fuel ratio sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

6.INSPECT A/F RELAY
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C124-1 (HAF2) - C111-6 (HAF2) Always Below 1 Ω
C124-1 (HAF2) or C111-6 (HAF2) - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE AIR FUEL RATIO SENSOR

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.INSPECT A/F RELAY

Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (A/F RELAY - A/F SENSOR)

NG

11.REPLACE A/F RELAY
7.CHECK HARNESS AND CONNECTOR (A/F RELAY - A/F SENSOR)
a.

Disconnect the air fuel ratio sensor connector.


b.

Remove the A/F relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C124-2 (+B) - A/F relay terminal 3 Always Below 1 Ω
C124-2 (+B) or A/F relay terminal 3 - Body ground Always 10 kΩ or higher



d.

Reconnect the air fuel ratio sensor connector.


e.

Reinstall the A/F relay.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (A/F RELAY - NO. 1 INTEGRATION RELAY)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK HARNESS AND CONNECTOR (A/F RELAY - NO. 1 INTEGRATION RELAY)
a.

Remove the A/F relay from the engine room relay block and junction block assembly.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F relay terminal 1- 1J-5 Always Below 1 Ω
A/F relay terminal 2 - Body ground Always Below 1 Ω
A/F relay terminal 1 or 1J-5 - Body ground Always 10 kΩ or higher



d.

Reinstall the A/F relay.


e.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (A/F RELAY - BATTERY)

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
9.CHECK HARNESS AND CONNECTOR (A/F RELAY - BATTERY)
a.

Disconnect the negative battery terminal.


b.

Disconnect the positive battery terminal.


c.

Remove the A/F relay from the engine room relay block and junction block assembly.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A/F relay terminal 5 - Positive battery terminal Always Below 1 Ω
A/F relay terminal 5 or Positive battery terminal - Body ground Always 10 kΩ or higher



e.

Reinstall the A/F relay.


f.

Reconnect the positive battery terminal.


g.

Reconnect the negative battery terminal.


Result:
Proceed to
OK
NG



OK

10.CHECK ECM POWER SOURCE CIRCUIT

NG

12.REPAIR OR REPLACE HARNESS OR CONNECTOR
10.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE A/F RELAY
a.

Replace the A/F relay.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
12.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace harness or connector.


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON.


e.

Turn the tester on.


f.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

HINT:

"Exhaust Temperature B1S1" on the intelligent tester screen should be 200°C (392°F) or higher.



g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0031 and/or P0032.


iii.

Check that STATUS is NORMAL.

HINT:
·

If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.

·

If STATUS is INCOMPLETE or N/A, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more again.





Result:
Proceed to
NEXT



NEXT

END