Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate that the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the intelligent tester, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) Ignition switch is ON.
(b) Brake pedal is released.
(c) The STP signal is off when the ST1- signal is off, or the STP signal is on when the ST1- signal is on.
·

Open or short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch

·

ECM


- DTC stored

Related Data List
DTC No. Data List
P0504 Stop Light Switch

CONFIRMATION DRIVING PATTERN

P0504
DTC Detection Drive Pattern Depress and release brake pedal with ignition switch ON

WIRING DIAGRAM

A160611
0.927,0.885 2.229,1.156 1.302,0.271 10 false from Ignition Switch 1.354,1.865 2.177,2.115 0.823,0.25 10 false from Battery 2.792,0.708 3.115,0.948 0.323,0.24 10 false IGN 4.563,1.802 4.76,2.021 0.198,0.219 10 false 1 5.906,3.104 6.396,3.396 0.49,0.292 10 false ECM 3.438,1.802 3.615,2.01 0.177,0.208 10 false 2 3.417,0.792 3.604,1.052 0.188,0.26 10 false 3 5.396,0.813 5.563,1.042 0.167,0.229 10 false 9 5.396,1.792 5.573,2.01 0.177,0.219 10 false 8 5.615,0.813 6.031,1.073 0.417,0.26 10 false ST1- 5.615,1.792 6.042,2.021 0.427,0.229 10 false STP 4.563,0.802 4.75,1.073 0.188,0.271 10 false 4 2.74,1.708 3.167,1.958 0.427,0.25 10 false STOP 3.479,2.396 4.625,2.677 1.146,0.281 10 false Stop Light Switch 5.906,2.958 6.344,3.167 0.438,0.208 10 false G149 3.469,2.208 3.813,2.417 0.344,0.208 10 false A24

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the intelligent tester.

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the tester on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

5.

Check Stop Light Switch when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed ON
Released OFF

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



PROCEDURE

1.CHECK STOP LIGHT SWITCH ASSEMBLY (TERMINAL B VOLTAGE)
a.
A253393C03
0.823,1.031 1.188,1.313 0.365,0.281 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 0.885,1.094 1.198,1.292 0.313,0.198 10 false A24
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-2 - Body ground Always 11 to 14 V
A24-3 - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the stop light switch connector.


Result:
Proceed to
OK
NG



OK

2.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK ECM (STP AND ST1- VOLTAGE)

NG

5.REPLACE STOP LIGHT SWITCH ASSEMBLY
3.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A220581
0.344,2.604 0.781,2.854 0.438,0.25 0.281,3.865 0.604,3.219 true 0.99,3.865 0.667,3.219 true 0.125,0.604 0.438,0.802 0.313,0.198 10 false *a 0.115,2.417 0.427,2.615 0.313,0.198 10 false *c 1.667,0.667 1.979,0.865 0.313,0.198 10 false *b 0.406,2.646 0.927,2.917 0.521,0.271 10 false G149 0.115,3.906 0.708,4.167 0.594,0.26 10 false 9 (ST1-) 0.865,3.906 1.438,4.229 0.573,0.323 10 false 8 (STP)
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Brake Pedal Condition Specified Condition
G149-9 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
G149-8 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Depress and release the brake pedal.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END