For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).
If P2237, P2238 and/or P2239 is present, refer to the DTC table for DPF system (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>SYSTEM DESCRIPTION).
These DTCs are recorded when the air fuel ratio sensor has a malfunction, although the title is the oxygen sensor.
The air fuel ratio sensor has the characteristic of providing output voltage which is proportional to the air-fuel ratio. The air fuel ratio sensor output voltage* is used by the ECM to control the air-fuel ratio.
The air fuel ratio sensor is located after the DPF catalytic converter. This sensor has been developed based on the structure and technology of a sensor that is being used for gasoline engines. The cover portion of the sensor has been changed for use in the diesel engine with DPF in order to eliminate the influence of the sensor temperature and particulate matter (PM).
In order to reduce both PM, the ECM adjusts the air-fuel ratio to slightly rich (but it is lean compared with the stoichiometric air-fuel ratio) based on signals from the air fuel ratio sensor. When the ECM performs PM forced regeneration using adding fuel using the exhaust fuel addition injector, the air-fuel ratio is also properly adjusted using the sensor.
*: The voltage value changes inside the ECM only.
The ECM provides a pulse width modulated control circuit to adjust current through the heater. The air fuel ratio sensor heater circuit uses a relay on the B+ side of the circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2237 | Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) | When either of the following conditions is met (1 trip detection logic):
·
Air fuel ratio sensor circuit malfunction ·
The resistance of the air fuel ratio sensor element is 250 Ω or higher for 5 seconds or more. |
Main trouble area: Open in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| P2238 | Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) | Air fuel ratio sensor circuit low (bank 1 sensor 1)
(1 trip detection logic) |
Main trouble area: Open in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| P2239 | Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) | Air fuel ratio sensor circuit high (bank 1 sensor 1)
(1 trip detection logic) |
Main trouble area: Short in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| P2252 | Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) | Air fuel ratio sensor circuit low (bank 1 sensor 1)
(1 trip detection logic) |
Main trouble area: Open in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| P2253 | Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) | Air fuel ratio sensor circuit high (bank 1 sensor 1)
(1 trip detection logic) |
Main trouble area: Short in air fuel ratio sensor circuit
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2237 | ·
AFS Voltage B1S1 ·
Exhaust Temperature B1S1 |
| P2238 | |
| P2239 | |
| P2252 | |
| P2253 |
| DTC Detection Drive Pattern | ·
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more. ·
Check that "Exhaust Temperature B1S1" displays 200°C (392°F) or higher using the intelligent tester. |
| DTC Detection Drive Pattern | Ignition switch ON for 7 seconds |
The air fuel ratio sensor outputs a voltage in proportion to the air-fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.
Refer to DTC P0031 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>P0031).
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).
After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C124-3 (AF2+) - C111-2 (AF2+) | Always | Below 1 Ω |
| C124-4 (AF2-) - C111-1 (AF2-) | Always | Below 1 Ω |
| C124-3 (AF2+) or C111-2 (AF2+) - Body ground | Always | 10 kΩ or higher |
| C124-4 (AF2-) or C111-1 (AF2-) - Body ground | Always | 10 kΩ or higher |
Reconnect the air fuel ratio sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>AIR FUEL RATIO SENSOR(w/ DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Warm up the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Warm up the engine.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
Make sure that the exhaust gas temperature (Exhaust Temperature B1S1) is 200°C (392°F) or higher.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT