Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  P007C  Charge Air Cooler Temperature Sensor Circuit Low  P007D  Charge Air Cooler Temperature Sensor Circuit High  


DESCRIPTION

A208462
1.479,2 1.635,1.76 1.635,1.76 1.781,1.76 false 0.208,0.198 0.688,0.375 0.479,0.177 10 false (Fig. 1) 0.208,0.542 1.198,0.719 0.99,0.177 10 false Resistance kΩ 1.854,1.677 2.583,1.948 0.729,0.271 10 false Acceptable 1.208,4.063 2.542,4.344 1.333,0.281 10 false Temperature °C (°F)

The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P007C Charge Air Cooler Temperature Sensor Circuit Low Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Short in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored
P007D Charge Air Cooler Temperature Sensor Circuit High Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds (1 trip detection logic).
·

Open in intake air temperature sensor (turbo) circuit

·

Intake air temperature sensor (turbo)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P007C Intake Air Temp (Turbo)
P007D

HINT:

If DTC P007C or P007D is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power




CONFIRMATION DRIVING PATTERN

P007C, P007D
DTC Detection Drive Pattern Ignition switch ON for 1 second

WIRING DIAGRAM

A276464
0.542,2.156 2.969,2.417 2.427,0.26 10 false Intake Air Temperature Sensor (Turbo) 5.906,2.417 6.365,2.625 0.458,0.208 10 false ECM 6.25,0.208 6.635,0.469 0.385,0.26 10 false 5 V 5.552,0.646 5.917,0.875 0.365,0.229 10 false THIA 5.552,1.25 6.01,1.427 0.458,0.177 10 false E2 6.156,0.521 6.344,0.708 0.188,0.188 10 false R 2.448,1.271 2.74,1.5 0.292,0.229 10 false 1 2.448,0.656 2.646,0.885 0.198,0.229 10 false 2 5.281,0.573 5.427,0.781 0.146,0.208 10 false 3 5.229,1.177 5.438,1.354 0.208,0.177 10 false 14 5.135,0.76 5.552,0.969 0.417,0.208 10 false C113 0.542,1.958 0.875,2.177 0.333,0.219 10 false C18 5.135,1.375 5.552,1.573 0.417,0.198 10 false C114

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTAKE AIR TEMPERATURE [TURBO])
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

d.

Read the value.

OK:

Same as air temperature near intake manifold


Result:
Result Proceed to
-40°C (-40°F) A
140°C (284°F) or higher B
OK (same as air temperature near intake manifold) C


HINT:
·

If there is an open circuit, the tester indicates -40°C (-40°F).

·

If there is a short circuit, the tester indicates 140°C (284°F) or higher.





A

2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

B

7.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

C

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
2.READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)
a.
A204915
0.646,3.656 1.052,3.906 0.406,0.25 0.667,0.479 0.948,0.729 0.281,0.25 10 false *1 2.646,0.448 2.906,0.646 0.26,0.198 10 false *2 2.406,1.365 2.813,1.635 0.406,0.271 10 false THIA 2.458,1.813 2.802,2.073 0.344,0.26 10 false E2 0.75,3.292 1.031,3.521 0.281,0.229 10 false *a 0.719,3.688 1.104,3.948 0.385,0.26 10 false C18
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM
*a Front view of wire harness connector
(to Intake Air Temperature Sensor (Turbo))


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON and turn the tester on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

f.

Read the value.

OK:

140°C (284°F) or higher



g.

Reconnect the intake air temperature sensor (turbo) connector.


Result:
Proceed to
OK
NG



OK

3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
3.CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-2 - C113-3 (THIA) Always Below 1 Ω
C18-1 - C114-14 (E2) Always Below 1 Ω



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)
a.
A302633
0.771,0.25 1.083,0.448 0.313,0.198 10 false *1 2.604,0.25 2.917,0.448 0.313,0.198 10 false *2 2.5,1.135 2.875,1.396 0.375,0.26 10 false THIA 2.479,1.51 2.844,1.771 0.365,0.26 10 false E2
*1 Intake Air Temperature Sensor (Turbo)
*2 ECM


Disconnect the intake air temperature sensor (turbo) connector.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

Powertrain > Engine > Data List
Tester Display
Intake Air Temp (Turbo)
50003 61 240

e.

Read the value.

OK:

-40°C (-40°F)



f.

Reconnect the intake air temperature sensor (turbo) connector.


Result:
Proceed to
OK
NG



OK

8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

NG

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
8.REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 1 second.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

10.CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)
a.

Disconnect the intake air temperature sensor (turbo) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C18-2 or C113-3 (THIA) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air temperature sensor (turbo) connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

11.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
11.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED