Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for DPF) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052104 ECD SYSTEM(for DPF) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for DPF)  Turbocharger Noise  


DESCRIPTION

HINT:

Turbocharger noise is classified into 2 types. One is whistling noise, and the other is whining noise. When troubleshooting, the type of noise should be determined first.


Description
Noise Type Noise Description Main Trouble Area
Whistling noise The volume and pitch of this noise are proportional to turbocharger speed or engine speed. Therefore, the noise level will become more obvious when engine speed increases.
·

Turbocharger (e.g. shaft imbalance)

·

Balance shaft gear

·

Transmission gear

·

Intake air system leakage

·

Intake air system breakage


Whining noise This noise has a lower pitch than whistling noise. It generally occurs in the engine speed range of 1500 to 2500 rpm, and has a relatively constant pitch, independent of engine speed and vehicle speed. Turbocharger
HINT:
·

Example: Vibration of turbocharger is transferred to exhaust pipe which causes resonation and noise.

·

Example: Vibration of turbocharger is transferred through exhaust pipe to vehicle body (floor) which then vibrates causing noise.




Faults and Symptoms of Diesel Engine Components


Turbocharger System
Main fault Turbocharger turbine shaft imbalance
Symptoms High-pitched whistling noise
HINT:

The pitch and volume change in proportion to the turbocharger speed.



Intake System
Main fault Leakage
Symptoms Leak flow noise

Balance Shaft Gear
Symptoms Gear noise
HINT:

The pitch and volume change in proportion to the engine speed.



Transmission Gear
Symptoms Gear noise
HINT:

The pitch and volume change in proportion to the transmission gear speed.




CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for DPF)>REGISTRATION).



PROCEDURE

1.CONFIRM CONDITION IN WHICH NOISE OCCURRED
a.

Confirm with the customer the conditions in which the noise occurred.

HINT:

To clearly understand the conditions in which the noise occurred, the items in the table below are useful.


Item Note
Engine speed Engine speed range
Vehicle speed Vehicle speed range
Transmission gear Which gear?
Accelerator pedal position During acceleration or deceleration?
Temperature
·

Ambient temperature

·

Engine temperature (cold, warmed up, etc.)


Road conditions
·

City or highway driving

·

Uphill or downhill


Noise level
·

Did the noise occur suddenly, or build gradually?

·

Has the noise gradually been getting louder?


Other symptoms
·

Lack of power

·

High fuel consumption, etc.


Noise recognition What made the customer determine the noise to be abnormal?


Result:
Proceed to
NEXT



NEXT

2.CONFIRM NOISE CUSTOMER MENTIONED (PROCEDURE 2)
2.CONFIRM NOISE CUSTOMER MENTIONED (PROCEDURE 2)
a.

Check for the noise described by the customer.

HINT:

If a noise is heard, make sure that the noise matches the noise described by the customer.


Result:
Result Proceed to
Obvious abnormal noise matching noise described by customer is confirmed A
Obvious abnormal noise matching noise described by customer is not confirmed B




A

3.CHECK INTAKE SYSTEM

B

6.EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL
3.CHECK INTAKE SYSTEM
a.

Check for air leakage between the air cleaner and turbocharger, and between the turbocharger and intake manifold.

HINT:
·

Check for disconnected or improperly connected hoses, and gaps between hoses and parts.

·

Check for foreign matter between the air cleaner and turbocharger.




Result:
Proceed to
OK
NG



OK

4.CONFIRM NOISE SOURCE (FORM TURBOCHARGER OR NOT)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

4.CONFIRM NOISE SOURCE (FORM TURBOCHARGER OR NOT)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VN Turbo Open.

Powertrain > Engine > Active Test
Tester Display
Activate the VN Turbo Open
50004 61 182

e.

Perform the Active Test under the conditions* from the time the noise occurred described by the customer and compare the noise to the noise heard when not performing the Active Test and check if the noise is reduced.

HINT:

*: Some examples of conditions are idling, racing the engine and driving at full throttle.


Result:
Result Proceed to
The noise is reduced (or disappears) A
The noise is the same as in Procedure 2 (The noise does not change) B


HINT:
·

By performing Activate the VN Turbo Open Active Test, the variable nozzle of the turbocharger becomes fully open regardless of the engine condition, and the turbocharger speed does not increase.

·

If the turbocharger is the cause of the noise, the noise will be reduced when Activate the VN Turbo Open Active Test is performed because turbocharger speed does not increase.





A

5.CONFIRM THE NOISE TYPE

B

7.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 7)
5.CONFIRM THE NOISE TYPE
a.

Check whether the noise can be heard even when the engine speed is more than 3000 rpm, and whether the noise gradually gets louder as the engine speed increases.

HINT:

If so, the noise is likely to be whistling noise. If not, the noise is likely to be whining noise.


Result:
Result Proceed to
Yes (The noise is likely to be whistling noise) A
No (The noise is likely to be whining noise) B




A

B

10.PERFORM ALIGNMENT OF EXHAUST PIPE AND CONFIRM THE NOISE
6.EXPLAIN TO THE CUSTOMER THAT THE NOISE IS NORMAL
a.

Explain to the customer that the noise the customer mentioned is not abnormal.

HINT:

To help the customer understand, test driving another car with the customer may be helpful.



Result:
Proceed to
NEXT



NEXT

END

7.CHECK FOR NOISE FROM SOURCE OTHER THAN TURBOCHARGER (PROCEDURE 7)
a.

Check for the noise source.

1.

Start the engine

2.

Race the engine and check if the noise reduces at the same time the engine speed decreases.


HINT:
·

If the noise reduces at the same time the engine speed decreases, it is gear noise.

·

If the noise reduces a short time after the engine speed decreases, it is turbocharger noise.




Result:
Proceed to
NEXT



NEXT

8.REPLACE THE PARTS DETECTED IN PROCEDURE 7
8.REPLACE THE PARTS DETECTED IN PROCEDURE 7
a.

Replace the parts detected in Procedure 7 as the noise source.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check whether the noise problem has been successfully solved.


Result:
Proceed to
NEXT



NEXT

END

10.PERFORM ALIGNMENT OF EXHAUST PIPE AND CONFIRM THE NOISE
a.

Disconnect the front exhaust pipe assembly at the ball joint and from each exhaust pipe support, and then realign the exhaust pipe and reconnect it to each exhaust pipe support and at the ball joint.

Click hereEngine / Hybrid System>1KD-FTV INTAKE / EXHAUST>EXHAUST PIPE(w/ DPF)>INSTALLATION

A258906
0.219,3.885 1.51,4.063 1.292,0.177 4.396,2.719 5.115,2.896 0.719,0.177 0.583,2.927 1.302,3.104 0.719,0.177 0.938,2.927 0.938,2.625 false 4.74,2.083 4.74,2.719 false 0.646,1.417 0.917,0.854 0.917,0.854 1.073,0.854 false 0.885,1.896 1.063,1.51 1.063,1.51 1.156,1.51 false 2.167,2.177 2.698,0.958 2.698,0.958 2.854,0.958 false 3.552,3.438 3.115,3.719 3.115,3.719 3.115,3.823 false 5.302,0.979 5.552,0.354 5.552,0.354 5.698,0.354 false 5.969,1.646 6.688,2.094 6.688,2.094 6.688,2.271 false 3.958,1.969 4.135,0.99 4.135,0.99 4.229,0.99 false 4.521,2.146 4.052,2.615 4.052,2.615 4.052,2.833 false 6.625,2.333 6.833,2.5 0.208,0.167 10 false *7 3.052,3.854 3.271,4.042 0.219,0.188 10 false *4 0.25,3.885 1.531,4.094 1.281,0.208 10 false N*m (kgf*cm, ft.*lbf) 1.531,3.896 1.979,4.083 0.448,0.188 10 false : *a 0.375,4.24 0.698,4.427 0.323,0.188 10 false *b 1.313,1.438 1.573,1.635 0.26,0.198 10 false *2 4.385,0.906 4.594,1.104 0.208,0.198 10 false *5 4.458,2.729 5.177,2.948 0.719,0.219 8 false 43 (438, 32) 0.635,2.938 1.396,3.167 0.76,0.229 8 false 54 (544, 40) 3.958,2.896 4.208,3.094 0.25,0.198 10 false *6 1.115,0.771 1.323,0.958 0.208,0.188 10 false *1 2.906,0.875 3.146,1.042 0.24,0.167 10 false *3 0.656,2.552 0.885,2.729 0.229,0.177 10 false x 3 3.656,3.417 3.885,3.594 0.229,0.177 10 false x 2 4.792,2.115 5.021,2.292 0.229,0.177 10 false x 2 5.719,0.281 5.938,0.469 0.219,0.188 10 false *4 4.49,2.198 4.719,2.375 0.229,0.177 10 false x 2 5.417,0.969 5.646,1.146 0.229,0.177 10 false x 3 1.198,1.417 1.333,1.604 0.135,0.188 10 false ● 0.469,2.917 0.604,3.104 0.135,0.188 10 false ● 0.281,4.24 0.417,4.427 0.135,0.188 10 false ● 4.281,0.896 4.417,1.083 0.135,0.188 10 false ●
*1 Outlet Pipe *2 Gasket
*3 Front Exhaust Pipe Assembly *4 Exhaust Pipe Support
*5 Gasket (Ball Joint) *6 Compression Spring
*7 Center Exhaust Pipe Assembly - -
*a Specified Torque *b Non-reusable Part



b.

Confirm whether the noise problem is solved or not.

HINT:

The alignment of the exhaust pipe affects whining noise.


Result:
Result Proceed to
The noise problem is solved A
The noise problem remains B




A

END

B