Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0100  Mass Air Flow Circuit Malfunction  


DESCRIPTION

The intake mass air flow meter assembly consists of a platinum hot wire, temperature sensor and control circuit installed in a plastic housing. The temperature sensor (located in the intake air by-pass of the housing) detects the intake air temperature.

There is little variation in the output from the intake mass air flow meter assembly, as it is hardly affected by the resistance of the wire harness.

The internal circuit of the intake mass air flow meter assembly contains a hot wire and cold wire. A voltage is output through a bridge circuit (refer to the illustration) indicating the cooling of the hot wire according to the intake air amount. This voltage is then converted into a periodic signal by the periodic signal conversion circuit and output to the ECM. The frequency varies between approximately 1945 and 8500 Hz depending on the air flow rate. The ECM calculates the mass air flow rate based on this frequency.

A221589E04
2.031,1.271 1.854,1.271 1.854,1.271 1.667,1.74 false 0.49,2.729 0.49,2.115 0.49,2.115 1.271,1.823 true 2.719,1.635 2.604,1.635 2.604,1.635 2.417,1.948 false 4.052,2.917 4.052,2.5 4.052,2.5 4.51,1.906 true 6.031,3.26 6.031,2.927 6.031,2.927 4.813,2.125 true 1.688,0.542 2.042,0.76 0.354,0.219 10 false +B 1.635,0.865 2.813,1.135 1.177,0.271 10 false Power Transistor 2.771,1.552 3.969,1.906 1.198,0.354 10 false Output Voltage 2.146,2.323 3.177,2.854 1.031,0.531 10 false Periodic Signal Conversion Circuit 2.198,3.302 3.385,3.563 1.188,0.26 10 false Output Frequency 0.073,2.74 1.333,3.26 1.26,0.521 10 false Temperature Sensor (Thermistor) 2.063,1.198 3.802,1.51 1.74,0.313 10 false Platinum Hot Wire (Heater) 3.542,2.927 5.208,3.198 1.667,0.271 10 false Platinum Hot Wire (Heater) 4.979,3.271 7.042,3.573 2.063,0.302 10 false Temperature Sensor (Thermistor)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0100 Mass Air Flow Circuit Malfunction Mass air flow meter signal frequency is less than 850 Hz with the engine speed at 400 rpm or more for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0100 MAF

HINT:

If DTC P0100 is stored, the following symptoms may appear (as the ECM mistakenly determines that there is less air than the actual intake air amount, EGR is decreased according to the target EGR):

·

Combustion noise worsens




CONFIRMATION DRIVING PATTERN

P0100
DTC Detection Drive Pattern 3 seconds after engine is started

WIRING DIAGRAM

A276466E07
1.563,1.698 3.365,1.927 1.802,0.229 10 false No. 1 Integration Relay 3.719,2.063 5.146,2.292 1.427,0.229 10 false Mass Air Flow Meter 6.177,3.271 6.646,3.438 0.469,0.167 10 false ECM 0.469,2.354 1.094,2.552 0.625,0.198 10 false BATT P/I 1.229,0.583 1.646,0.771 0.417,0.188 10 false EFI 1.813,1.417 2.281,1.604 0.469,0.188 10 false MAIN 5.75,0.948 6.198,1.177 0.448,0.229 10 false VG 5.75,1.448 6.219,1.635 0.469,0.188 10 false EVG 5.74,2.719 6.219,2.906 0.479,0.188 10 false MREL 5.344,1.042 5.74,1.229 0.396,0.188 10 false C167 5.344,1.542 5.76,1.729 0.417,0.188 10 false C167 5.333,2.802 5.698,2.99 0.365,0.188 10 false G156 5.406,0.865 5.708,1.052 0.302,0.188 10 false 13 5.417,1.365 5.656,1.552 0.24,0.188 10 false 14 5.427,2.625 5.604,2.813 0.177,0.188 10 false 11 5.073,0.917 5.229,1.104 0.156,0.188 10 false 5 5.073,1.438 5.25,1.625 0.177,0.188 10 false 4 3.688,0.615 3.938,0.823 0.25,0.208 10 false 3 3.688,1.927 4.083,2.115 0.396,0.188 10 false C115 2.51,0.719 2.729,0.906 0.219,0.188 10 false 1J 2.51,1.073 2.729,1.26 0.219,0.188 10 false 1J 2.552,0.552 2.729,0.74 0.177,0.188 10 false 5 2.552,0.896 2.74,1.083 0.188,0.188 10 false 2 0.729,0.719 1.073,0.917 0.344,0.198 10 false 1H 1.365,1.5 1.583,1.688 0.219,0.188 10 false 1J 0.771,0.542 0.948,0.729 0.177,0.188 10 false 1 1.156,1.49 1.344,1.677 0.188,0.188 10 false 3 1.156,0.833 1.333,1.021 0.177,0.188 10 false 1 1.396,0.833 1.583,1.021 0.188,0.188 10 false 2 0.594,3.01 1.073,3.219 0.479,0.208 10 false Battery 3.833,0.615 4.156,0.76 0.323,0.146 10 false +B 4.802,0.802 5.021,0.948 0.219,0.146 10 false FG 4.708,1.438 5.063,1.615 0.354,0.177 10 false E2G 2.938,0.583 3.635,0.771 0.698,0.188 10 false EFI NO. 2 3.01,0.854 3.188,1.042 0.177,0.188 10 false 1 3.26,0.854 3.448,1.042 0.188,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
a.
A127724C08
0.375,1 0.76,1.24 0.385,0.24 1.375,1.75 1.677,1.146 true 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a 0.396,1.042 0.76,1.24 0.365,0.198 10 false C115 1.26,1.771 1.573,1.969 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C115-3 (+B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
2.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-5 (FG) - C167-13 (VG) Always Below 1 Ω
C115-4 (E2G) - C167-14 (EVG) Always Below 1 Ω
C115-5 (FG) or C167-13 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.REPLACE MASS AIR FLOW METER

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.REPLACE MASS AIR FLOW METER

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Read the DTCs.

Result:
Result Proceed to
P0100 is output A
No DTC is output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Start the engine and wait for 3 seconds or more.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

e.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C115-3 (+B) - 1J-5 Always Below 1 Ω
C115-3 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reinstall the No. 1 integration relay.


Result:
Proceed to
OK
NG



OK

8.CHECK ECM POWER SOURCE CIRCUIT

NG

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.CHECK ECM POWER SOURCE CIRCUIT

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED