Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The vehicle speed sensor outputs a 4 pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the ECM. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A112414E03
1.635,1.906 2.521,2.073 0.885,0.167 10 false Transmission 3.156,1.906 4.375,2.073 1.219,0.167 10 false Combination Meter 5.135,1.906 5.521,2.073 0.385,0.167 10 false ECM 2.469,0.427 3.438,0.625 0.969,0.198 10 false Pulse Signal 4.135,0.427 5.104,0.656 0.969,0.229 10 false Pulse Signal

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor "A" Conditions (a), (b) and (c) are met for 8 seconds or more (2 trip detection logic):
(a) Engine coolant temperature is higher than 70°C (158°F).
(b) Injection volume is 19 mm3/st or more.
(c) No speed signal is input to the ECM.
Conditions (a) and (b) are met for 5 seconds or more (2 trip detection logic):
(a) The fuel-cut operation is being performed.
(b) No speed signal is input to the ECM.
·

Open or short in speed signal circuit

·

Vehicle speed sensor

·

Combination meter assembly

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0500 Vehicle Speed

CONFIRMATION DRIVING PATTERN

P0500
DTC Detection Drive Pattern Drive the vehicle at 10 km/h (6.3 mph) or more

WIRING DIAGRAM

A206532E31
6.281,0.615 6.531,0.771 0.25,0.156 10 false 5 V 5.521,0.885 6.135,1.073 0.615,0.188 10 false SPD 5.271,0.938 5.604,1.156 0.333,0.219 10 false 30 6.031,1.865 6.552,2.052 0.521,0.188 10 false G156 6.031,2.021 6.552,2.24 0.521,0.219 10 false ECM 4.354,1.063 4.677,1.219 0.323,0.156 10 false 2P 3.448,1.052 3.875,1.24 0.427,0.188 10 false 2Q 4.365,0.854 4.719,1.042 0.354,0.188 10 false 26 3.458,0.854 3.792,1.052 0.333,0.198 10 false 26 3.344,1.427 4.792,1.813 1.448,0.385 10 false Driver Side Junction Block Assembly 2.594,0.948 2.885,1.104 0.292,0.156 10 false 6 0.917,1.042 1.25,1.25 0.333,0.208 10 false 5 0.833,1.865 1.427,2.031 0.594,0.167 10 false G19 2.302,0.969 2.667,1.167 0.365,0.198 10 false +S 1.094,1.031 1.521,1.26 0.427,0.229 10 false SI 0.833,2.01 2.729,2.333 1.896,0.323 10 false Combination Meter Assembly 0.104,2.688 2.094,2.969 1.99,0.281 10 false from Speed Sensor (SP1)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Vehicle Speed.

Powertrain > Engine > Data List
Tester Display
Vehicle Speed
50003 61 316

e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK COMBINATION METER SYSTEM
2.CHECK COMBINATION METER SYSTEM
a.

Inspect the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


b.

During inspection for the meter section, if there is an instruction that indicates to go back to inspections for each system, proceed to the next step.


Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the combination meter assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-6 (+S) - G156-30 (SPD) Always Below 1 Ω



d.

Reconnect the combination meter assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the driver side junction block assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-26 - G156-30 (SPD) Always Below 1 Ω



d.

Reconnect the driver side junction block assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY CONNECTOR IS DEFECTIVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY CONNECTOR - ECM)