Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.04–2012.10
RM1840EF _58 Vehicle Interior _009643 METER / GAUGE / DISPLAY _0052702 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

The vehicle speed signal consists of pulses sent to the combination meter assembly from the speedometer sensor.

NOTICE:

If the speedometer operation is not normal, refer to "Speedometer Malfunction" (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).


WIRING DIAGRAM

E252838
0.583,0.948 2.01,1.25 1.427,0.302 10 false Speedometer Sensor 4.938,1.417 5.073,1.656 0.135,0.24 10 false 6 4.948,0.365 5.094,0.573 0.146,0.208 10 false 5 0.354,2 2.219,2.354 1.865,0.354 10 false Radio Receiver Assembly*1 0.25,3.073 2.396,3.375 2.146,0.302 10 false Navigation Receiver Assembly*3 2.875,1.344 2.979,1.5 0.104,0.156 10 false 4 1.802,0.344 1.917,0.5 0.115,0.156 10 false 3 1.563,0.448 1.781,0.729 0.219,0.281 10 false SI 5.125,0.573 5.427,0.813 0.302,0.24 10 false SI 5.125,1.635 5.354,1.833 0.229,0.198 10 false +S 1.427,1.448 1.792,1.677 0.365,0.229 10 false SPD 1.781,1.427 2.021,1.625 0.24,0.198 10 false 17 0.167,6.615 1.031,6.865 0.865,0.25 10 false *4: for 4WD 0.167,7.865 2.104,8.281 1.938,0.417 10 false *8: for 1KD-FTV, 2KD-FTV 0.167,7.552 2.833,7.802 2.667,0.25 10 false *7: w/ Automatic Air Conditioning System 0.167,5.594 1.938,5.948 1.771,0.354 10 false *1: for Radio Receiver Type 0.167,5.948 2.073,6.229 1.906,0.281 10 false *2: for Radio and Display Type 0.167,7.25 2.073,7.5 1.906,0.25 10 false *6: w/ Theft Deterrent System 0.167,6.938 2.115,7.26 1.948,0.323 10 false *5: for Automatic Transmission 4.885,2.365 6.771,2.677 1.885,0.313 10 false Combination Meter Assembly 5.146,4.521 5.5,4.729 0.354,0.208 10 false SPD 5.396,5.24 5.833,5.521 0.438,0.281 10 false ECM 4.885,2.198 5.177,2.354 0.292,0.156 10 false G19 0.344,1.844 0.635,2.104 0.292,0.26 10 false G1 0.25,2.896 0.719,3.177 0.469,0.281 10 false G152 0.844,4.083 1.583,4.302 0.74,0.219 10 false TCM*4, *5 1.823,3.427 2.094,3.594 0.271,0.167 10 false 25 1.375,3.438 1.771,3.625 0.396,0.188 10 false SPD1 0.833,3.917 1.135,4.073 0.302,0.156 10 false G41 0.198,5.167 2.302,5.49 2.104,0.323 10 false Theft Warning ECU Assembly*6 1.802,4.521 2.073,4.729 0.271,0.208 10 false 17 1.438,4.542 1.823,4.792 0.385,0.25 10 false SPD 0.188,5 0.49,5.156 0.302,0.156 10 false G29 3.74,1.344 3.979,1.583 0.24,0.24 10 false 26 0.583,0.792 0.906,0.948 0.323,0.156 10 false C38 3.719,1.531 3.99,1.729 0.271,0.198 10 false 2Q 3.75,4.406 4.01,4.667 0.26,0.26 10 false 26 3.729,4.615 3.979,4.823 0.25,0.208 10 false 2P 4.729,4.417 5.073,4.604 0.344,0.188 10 false 17*8 4.76,4.604 5.094,4.813 0.333,0.208 10 false G38 5.01,3.438 5.406,3.667 0.396,0.229 10 false SPD 4.365,4.052 6.792,4.354 2.427,0.302 10 false Air Conditioning Amplifier Assembly*7 4.844,3.417 5.01,3.688 0.167,0.271 10 false 9 4.354,3.854 4.708,4.083 0.354,0.229 10 false G94 2.844,3.333 3.042,3.49 0.198,0.156 10 false 10 2.833,3.542 3.188,3.76 0.354,0.219 10 false 2Q 3.74,3.344 3.938,3.5 0.198,0.156 10 false 10 3.74,3.542 3.969,3.698 0.229,0.156 10 false 2P 2.833,1.542 3.125,1.781 0.292,0.24 10 false 2Q 2.885,4.406 3.021,4.615 0.135,0.208 10 false 4 2.833,4.625 3.094,4.844 0.26,0.219 10 false 2P 2.771,5.323 4,5.813 1.229,0.49 10 false Driver Side Junction Block Assembly 0.25,2.531 2.854,2.875 2.604,0.344 10 false Radio and Display Receiver Assembly*2 0.24,2.354 0.74,2.552 0.5,0.198 10 false G127 0.167,6.281 1.729,6.552 1.563,0.271 10 false *3: w/ Navigation System

E252839
0.198,5.104 1.313,5.385 1.115,0.281 10 false *9: for 2TR-FE 5.5,0.51 5.844,0.75 0.344,0.24 10 false SPD 5.792,1.229 6.219,1.49 0.427,0.26 10 false ECM 5.5,2.104 5.844,2.313 0.344,0.208 10 false SPD 5.771,2.823 6.188,3.115 0.417,0.292 10 false ECM 5.5,3.667 5.865,3.896 0.365,0.229 10 false SPD 2.51,2.104 2.823,2.354 0.313,0.25 10 false SPD 2.531,0.51 2.844,0.76 0.313,0.25 10 false SPD 5.823,4.375 6.26,4.594 0.438,0.219 10 false ECM 2.073,2.844 2.479,3.021 0.406,0.177 10 false ECM 2.146,1.24 2.552,1.396 0.406,0.156 10 false ECM 5.125,0.406 5.396,0.677 0.271,0.271 10 false 8*9 5.094,0.594 5.427,0.854 0.333,0.26 10 false G88 4.99,2 5.396,2.25 0.406,0.25 10 false 16*10 5.021,2.198 5.417,2.438 0.396,0.24 10 false G146 5,3.552 5.427,3.813 0.427,0.26 10 false 30*11 5.021,3.74 5.406,3.969 0.385,0.229 10 false G148 2.99,0.406 3.396,0.563 0.406,0.156 10 false 8*12 2.958,0.604 3.375,0.917 0.417,0.313 10 false G154 2.906,1.99 3.333,2.24 0.427,0.25 10 false 30*13 2.917,2.198 3.292,2.469 0.375,0.271 10 false G156 0.198,5.427 1.521,5.698 1.323,0.271 10 false *10: for 2TR-FBE 0.198,5.781 2.583,6.125 2.385,0.344 10 false *11: for 1KD-FTV, 2KD-FTV (for DPF) 0.198,6.094 2.229,6.323 2.031,0.229 10 false *12: for 1GR-FE 0.198,6.417 2.292,6.719 2.094,0.302 10 false *13: for 1KD-FTV (for i-ART)

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.
E224872
1.448,0.198 1.969,0.458 0.521,0.26 1.458,2.25 1.979,2.51 0.521,0.26 0.396,0.177 0.573,0.344 0.177,0.167 10 false *a 1.625,0.25 1.906,0.406 0.281,0.156 10 false 2Q 1.646,2.302 1.927,2.458 0.281,0.156 10 false 2P
*a Front view of wire harness connector
(to Junction Connector)


Disconnect the 2Q driver side junction block assembly connector.


b.

Disconnect the 2P driver side junction block assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

HINT:

If the voltage is not as specified, it is possible that an ECU or circuit has a malfunction. The malfunctioning ECU or circuit will be diagnosed in the following steps.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
2Q-4 - Body ground*1, *2, *3 Ignition switch ON 4.5 to 14 V
2Q-10 - Body ground*4, *5 Ignition switch ON 4.5 to 14 V
2P-4 - Body ground*6 Ignition switch ON 4.5 to 14 V
2P-10 - Body ground*7 Ignition switch ON 4.5 to 14 V
2P-26 - Body ground Ignition switch ON 4.5 to 14 V


*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: w/ Navigation System

*4: for 1KD-FTV

*5: for Automatic Transmission

*6: w/ Theft Deterrent System

*7: w/ Automatic Air Conditioning System


Result:
Result Proceed to
Voltage is not as specified in one circuit A
Voltage is as specified in all circuits B




A

2.SYSTEM CHECK

B

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
2.SYSTEM CHECK
a.

Select the circuit for which the voltage was not as specified in the previous step.

Result:
Tester Connection System that Uses the Circuit Proceed to
2Q-4 - Body ground*1, *2, *3 Audio and visual system A
2Q-10 - Body ground*4, *5 Automatic transmission system B
2P-4 - Body ground*6 Theft deterrent system C
2P-10 - Body ground*7 Automatic air conditioning system D
2P-26 - Body ground SFI system*8 or ECD system*4, *9 E


*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: w/ Navigation System

*4: for 1KD-FTV

*5: for Automatic Transmission

*6: w/ Theft Deterrent System

*7: w/ Automatic Air Conditioning System

*8: for 2TR-FE, 2TR-FBE, 1GR-FE

*9: for 2KD-FTV




A

3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - RADIO RECEIVER OR RADIO AND DISPLAY OR NAVIGATION RECEIVER)

B

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - TCM)

C

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - THEFT WARNING ECU ASSEMBLY)

D

6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

E

7.CHECK ENGINE TYPE
3.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - RADIO RECEIVER OR RADIO AND DISPLAY OR NAVIGATION RECEIVER)

*1: for Radio Receiver Type

*2: for Radio and Display Type

*3: w/ Navigation System


a.

Disconnect the 2Q driver side junction block assembly connector.


b.

Disconnect the G1 radio receiver assembly*1 or G127 radio and display receiver assembly*2 connector.


c.

Disconnect the G152 navigation receiver assembly*3 connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2Q-4 - G1-17 (SPD)*1 Always Below 1 Ω
2Q-4 - G127-17 (SPD)*2 Always Below 1 Ω
2Q-4 - G152-17 (SPD)*3 Always Below 1 Ω
G1-17 (SPD) - Body ground*1 Always 10 kΩ or higher
G127-17 (SPD) - Body ground*2 Always 10 kΩ or higher
G152-17 (SPD) - Body ground*3 Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK (for Radio Receiver Type) B
OK (for Radio and Display Type) C
OK (w/ Navigation System) D




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE RADIO RECEIVER ASSEMBLY

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

D

4.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - TCM)
a.

Disconnect the 2Q driver side junction block assembly connector.


b.

Disconnect the G41 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2Q-10 - G41-25 (SPD1) Always Below 1 Ω
G41-25 (SPD1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - THEFT WARNING ECU ASSEMBLY)
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G29 theft warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-4 - G29-17 (SPD) Always Below 1 Ω
G29-17 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G94 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2P-10 - G94-9 (SPD) Always Below 1 Ω
G94-9 (SPD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Result
for Gasoline Engine A
for Diesel Engine B




A

8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)

B

9.CHECK HARNESS AND CONNECTOR
8.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - ECM)
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G154*1, G88*2 or G146*3 ECM connector.

*1: for 1GR-FE

*2: for 2TR-FE

*3: for 2TR-FBE



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE
Tester Connection Condition Specified Condition
2P-26 - G154-8 (SPD) Always Below 1 Ω
G154-8 (SPD) - Body ground Always 10 kΩ or higher

for 2TR-FE
Tester Connection Condition Specified Condition
2P-26 - G88-8 (SPD) Always Below 1 Ω
G88-8 (SPD) - Body ground Always 10 kΩ or higher

for 2TR-FBE
Tester Connection Condition Specified Condition
2P-26 - G146-16 (SPD) Always Below 1 Ω
G146-16 (SPD) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
NG A
OK (for 1GR-FE) B
OK (for 2TR-FE) C
OK (for 2TR-FBE) D




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

D

9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the 2P driver side junction block assembly connector.


b.

Disconnect the G38*1, G148*2 or G156*3 ECM connector.

*1: for 1KD-FTV, 2KD-FTV

*2: for 1KD-FTV, 2KD-FTV (for DPF)

*3: for 1KD-FTV (for i-ART)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1KD-FTV, 2KD-FTV
Tester Connection Condition Specified Condition
2P-26 - G38-17 (SPD) Always Below 1 Ω
G38-17 (SPD) - Body ground Always 10 kΩ or higher


for 1KD-FTV, 2KD-FTV (for DPF)
Tester Connection Condition Specified Condition
2P-26 - G148-30 (SPD) Always Below 1 Ω
G148-30 (SPD) - Body ground Always 10 kΩ or higher

for 1KD-FTV (for i-ART)
Tester Connection Condition Specified Condition
2P-26 - G156-30 (SPD) Always Below 1 Ω
G156-30 (SPD) - Body ground Always 10 kΩ or higher

Result:
Result Proceed to
NG A
OK (for 1KD-FTV) B
OK (for 2KD-FTV) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

10.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the 2Q driver side junction block assembly connector.


b.

Disconnect the G19 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2Q-26 - G19-6 (+S) Always Below 1 Ω
G19-6 (+S) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK COMBINATION METER ASSEMBLY
a.
E224603
1.229,0.563 1.708,0.906 0.479,0.344 2.375,0.625 2.292,0.625 2.292,0.625 1.792,1.406 true 2.885,3.625 3.24,3.823 0.354,0.198 10 false GND 2.438,0.531 2.792,0.729 0.354,0.198 10 false +S 1.333,0.656 1.635,0.854 0.302,0.198 10 false G19 0.292,0.625 0.469,0.823 0.177,0.198 10 false *a
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Reconnect the G19 combination meter assembly connector.


ii.

Remove the combination meter assembly with the connector(s) still connected.


iii.

Connect an oscilloscope to terminal G19-6 (+S) and body ground.


iv.

Turn the ignition switch to ON.


v.

Check the signal waveform according to the condition(s) in the table below.

Measurement Condition
Item Condition
Tester Connection G19-6 (+S) - Body ground
Tool Setting 5 V/DIV., 20 msec./DIV.
Condition Driving at approximately 20 km/h (12 mph)



Result:
Proceed to
OK
NG



OK

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY