Refer to DTC P2120 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P2120).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P2121 | Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance | The difference between VPA and VPA2 is less than 0.4 V, or more than 1.2 V for 0.5 seconds (1 trip detection logic). | ·
Accelerator pedal position sensor circuit ·
Accelerator pedal position sensor ·
ECM |
Comes on | DTC stored |
| DTC No. | Data List |
|---|---|
| P2121 | ·
Accel Position ·
Accel Sens. No.1 Volt % ·
Accel Sens. No.2 Volt % |
| DTC Detection Drive Pattern | Ignition switch ON
·
Accelerator pedal fully released for 3 seconds ·
Accelerator pedal depressed partway for 3 seconds ·
Accelerator pedal fully depressed for 3 seconds |
Refer to DTC P2120 (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>P2120).
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
| Tester Display |
|---|
| Accel Sens. No.1 Volt % |
| Accel Sens. No.2 Volt % |
| *1 | Accelerator Pedal Assembly |
| *a | Depressed |
| *b | Released |
Read the values.
| Accelerator Pedal | Accel Sens. No.1 Volt % | Accel Sens. No.2 Volt % |
|---|---|---|
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G6-1 (VCP2) - G156-4 (VCP2) | Always | Below 1 Ω |
| G6-2 (EPA2) - G156-3 (EPA2) | Always | Below 1 Ω |
| G6-3 (VPA2) - G157-1 (VPA2) | Always | Below 1 Ω |
| G6-4 (VCPA) - G156-6 (VCPA) | Always | Below 1 Ω |
| G6-5 (EPA) - G156-5 (EPA) | Always | Below 1 Ω |
| G6-6 (VPA) - G157-2 (VPA) | Always | Below 1 Ω |
| G6-1 (VCP2) or G156-4 (VCP2) - Body ground | Always | 10 kΩ or higher |
| G6-3 (VPA2) or G157-1 (VPA2) - Body ground | Always | 10 kΩ or higher |
| G6-4 (VCPA) or G156-6 (VCPA) - Body ground | Always | 10 kΩ or higher |
| G6-6 (VPA) or G157-2 (VPA) - Body ground | Always | 10 kΩ or higher |
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the accelerator pedal sensor assembly.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR
Turn the ignition switch to ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| P2121 is output | A |
| No DTC is output | B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT