Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0088  Fuel Rail / System Pressure - Too High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0088 Fuel Rail / System Pressure - Too High The fuel pressure of the common rail exceeds 220000 kPa (2243 kgf/cm2, 31900 psi) (1 trip detection logic).
·

Suction control valve

·

Open or short in suction control valve circuit

·

No. 1 injector assembly (fuel pressure sensor)

·

No. 4 injector assembly (fuel pressure sensor)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0088
·

Fuel Press

·

Fuel Pressure #1

·

Fuel Pressure #4

·

Target Common Rail Pressure

·

Target Pump SCV Current



HINT:
·

For more information on the fuel supply pump assembly (suction control valve) and common rail system, refer to System Description (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>SYSTEM DESCRIPTION).

·

When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine / Data List / Fuel Press.

Reference
Engine Speed Fuel Press
Idling Approximately 30000 to 50000 kPa
3000 rpm (No engine load) Approximately 60000 to 95000 kPa

·

Check "Fuel Press", "Target Common Rail Pressure" and "Target Pump SCV Current" in the freeze frame data.



CONFIRMATION DRIVING PATTERN

P0088
DTC Detection Drive Pattern After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

MONITOR DESCRIPTION

P0088 (Internal fuel pressure too high):

The ECM stores this DTC if the fuel pressure inside the common rail is higher than 220000 kPa (2243 kgf/cm2, 31900 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the fuel supply pump assembly, the ECM needs initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read Current DTCs.

Result:
Result Proceed to
P0088 is output A
P0088 and DTCs related to the fuel temperature circuit* are output B


HINT:
·

Fuel pressure sensor circuit DTC: P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3, P13E1, P13E2, P13E6, P13E7.

·

When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.





A

2.CHECK FREEZE FRAME DATA (FUEL PRESS)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.CHECK FREEZE FRAME DATA (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Record the stored DTCs and freeze frame data.

Result:
Result Proceed to
Value of Fuel Press is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data B
Except above A




A

3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

B

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A302635C10
1.333,0.156 1.771,0.438 0.438,0.281 0.479,1.615 1.365,0.74 true 1.198,1.604 1.365,0.792 true 1.885,1.594 1.625,0.802 true 2.469,1.635 1.635,0.74 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.396,0.208 1.813,0.427 0.417,0.219 10 false C166 0.229,1.667 0.75,1.875 0.521,0.208 10 false 6 (EIJ1) 0.917,1.667 1.563,1.885 0.646,0.219 10 false 12 (PIJ1) 1.667,1.667 2.198,1.875 0.531,0.208 10 false 9 (PIJ4) 2.313,1.667 2.833,1.875 0.521,0.208 10 false 3 (EIJ4)
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the No. 1 or No. 4 injector assembly and ECM.

A192849E06
2.115,1.875 3.073,0.688 3.073,0.688 3.167,0.688 false 3.104,1.875 3.74,1.51 3.74,1.51 3.823,1.51 false 3.854,1.396 5.865,1.958 2.01,0.563 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.219,0.604 5.406,1.094 2.188,0.49 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.583,0.292 2.333,0.531 0.75,0.24 10 false Example: 4.375,2.583 6.417,2.813 2.042,0.229 10 false Tester Range (Reference): 4.375,2.844 6.771,3.156 2.396,0.313 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C166-12 (PIJ1) - C166-6 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C166-9 (PIJ4) - C166-3 (EIJ4)


Result:
Result Proceed to
MIL comes on or noise present in the waveform B
Except above A




A

4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

B

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL SUPPLY PUMP(w/ Glow Plug Controller)>REMOVAL

HINT:

Before replacing the fuel supply pump assembly, check that the wire harness between the suction control valve and ECM is not shorted to ground.

When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 923 to 1123 mA when idling, and outside the range of 1013 to 1212 mA when the engine is running at 2500 rpm without load.

If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.

When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the fuel supply pump assembly.



Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
6.PERFORM FUEL SUPPLY PUMP INITIALIZATION
a.

Perform supply pump initialization.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION

Powertrain > Engine > Utility
Tester Display
Supply Pump Initialization
50005 61 163

Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0088.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P0088 is output A
All Readiness NORMAL B
ABNORMAL A


HINT:

If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.





A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A302635C11
1.333,0.156 1.771,0.438 0.438,0.281 0.479,1.615 1.365,0.74 true 1.198,1.604 1.365,0.792 true 1.885,1.594 1.625,0.802 true 2.469,1.635 1.635,0.74 true 0.094,0.052 0.406,0.25 0.313,0.198 10 false *a 1.396,0.208 1.813,0.427 0.417,0.219 10 false C166 0.229,1.667 0.75,1.875 0.521,0.208 10 false 6 (EIJ1) 0.917,1.667 1.563,1.885 0.646,0.219 10 false 12 (PIJ1) 1.667,1.667 2.198,1.875 0.531,0.208 10 false 9 (PIJ4) 2.313,1.667 2.833,1.875 0.521,0.208 10 false 3 (EIJ4)
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the No. 1 or No. 4 injector assembly and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
C166-12 (PIJ1) - C166-6 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C166-9 (PIJ4) - C166-3 (EIJ4)


Result:
Result Proceed to
MIL comes on or noise present in the waveform A
Except above B




A

11.REPLACE NO. 1 OR NO. 4 INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

B

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE NO. 1 OR NO. 4 INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
a.

Replace the No. 1 or No. 4 injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 61 20

ii.

Input DTC P0088.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.



Result:
Proceed to
NEXT



NEXT

END