Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P13C1  Fuel Temperature Sensor Circuit Low #1  P13C2  Fuel Temperature Sensor Circuit High #1  P13C3  Fuel Temperature Sensor Circuit Range/Performance #1  P13C6  Fuel Temperature Sensor Circuit Low #2  P13C7  Fuel Temperature Sensor Circuit High #2  P13C8  Fuel Temperature Sensor Circuit Range/Performance #2  P13CB  Fuel Temperature Sensor Circuit Low #3  P13CC  Fuel Temperature Sensor Circuit High #3  P13CD  Fuel Temperature Sensor Circuit Range/Performance #3  P13D1  Fuel Temperature Sensor Circuit Low #4  P13D2  Fuel Temperature Sensor Circuit High #4  P13D3  Fuel Temperature Sensor Circuit Range/Performance #4  


DESCRIPTION

The i-ART injector detects the fuel temperature from the sensors built into each injector assembly.

The fuel temperature detected inside the injector assembly is sent to the ECM as feedback through the communication line.

The ECM determines that there is a malfunction when the temperature data (voltage value) for each cylinder received from the injector assemblies via INJ communication are above or below a certain value, or when the difference in temperature with other cylinders exceeds a certain value.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P13C1 Fuel Temperature Sensor Circuit Low #1 The voltage value (communication result) from the fuel temperature sensor is 1.75 V or less for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13C2 Fuel Temperature Sensor Circuit High #1 The voltage value (communication result) from the fuel temperature sensor is 3.34 V or more for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13C3 Fuel Temperature Sensor Circuit Range/Performance #1 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


Comes on DTC stored
P13C6 Fuel Temperature Sensor Circuit Low #2 The voltage value (communication result) from the fuel temperature sensor is 1.75 V or less for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13C7 Fuel Temperature Sensor Circuit High #2 The voltage value (communication result) from the fuel temperature sensor is 3.34 V or more for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13C8 Fuel Temperature Sensor Circuit Range/Performance #2 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


Comes on DTC stored
P13CB Fuel Temperature Sensor Circuit Low #3 The voltage value (communication result) from the fuel temperature sensor is 1.75 V or less for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13CC Fuel Temperature Sensor Circuit High #3 The voltage value (communication result) from the fuel temperature sensor is 3.34 V or more for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13CD Fuel Temperature Sensor Circuit Range/Performance #3 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


Comes on DTC stored
P13D1 Fuel Temperature Sensor Circuit Low #4 The voltage value (communication result) from the fuel temperature sensor is 1.75 V or less for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13D2 Fuel Temperature Sensor Circuit High #4 The voltage value (communication result) from the fuel temperature sensor is 3.34 V or more for 3 seconds or more.
(1 trip detection logic)
·

Open or short in fuel temperature sensor (built into injector assembly) circuit

·

Fuel temperature sensor (built into injector assembly)

·

ECM


Comes on DTC stored
P13D3 Fuel Temperature Sensor Circuit Range/Performance #4 The voltage value (communication result) from the fuel temperature sensor differs by 23.6°C or more compared to other cylinders for 3 seconds or more.
(1 trip detection logic)
·

VIJ circuit malfunction

·

Fuel temperature sensor (built into injector assembly)

·

Harness or connector


Comes on DTC stored

Related Data List
DTC No. Data List
P13C1
P13C2
P13C6
P13C7
P13CB
P13CC
P13D1
P13D2
Fuel Temperature #1
Fuel Temperature #2
Fuel Temperature #3
Fuel Temperature #4
P13C3
P13C8
P13CD
P13D3

HINT:
·

If DTC P13C1, P13C2, P13C6, P13C7, P13CB, P13CC, P13D1 and/or P13D2 is stored, the following symptoms may appear:

·

Misfire

·

Combustion noise

·

Black smoke

·

White smoke

·

Lack of power


·

When DTC P13C1, P13C2, P13C3, P13C6, P13C7, P13C8, P13CB, P13CC, P13CD, P13D1, P13D2 and/or P13D3 is stored, check the fuel temperature by entering the following menus: Powertrain / Engine / Data List / Fuel Temperature #1 to #4.

Reference
Temperature Displayed Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) or higher Short circuit



CONFIRMATION DRIVING PATTERN

P13C1, P13C6, P13CB, P13D1, P13C2, P13C7, P13CC, P13D2, P13C3, P13C8, P13CD, P13D3
DTC Detection Drive Pattern Ignition switch ON for 8 seconds or more

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs

Result:
Result Proceed to
"Fuel pressure sensor circuit DTC" and "Injector Internal EEPROM Malfunction circuit DTC" are output*1 A
"Fuel pressure sensor circuit DTC" and "Fuel temperature sensor circuit" are output*2 B
Only DTCs related to the fuel temperature sensor circuit are output*3 C


HINT:
·

*1: Fuel pressure sensor circuit DTC and Injector Internal EEPROM Malfunction circuit DTCs:

Fuel pressure sensor circuit DTC: P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3.

Injector Internal EEPROM Malfunction circuit: P168A, P168B, P168C, P168D.

·

*2: Fuel pressure sensor circuit DTC:

P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3.

·

*3: Fuel temperature sensor circuit DTC:

P13C1, P13C2, P13C3, P13C6, P13C7, P13C8, P13CB, P13CC, P13CD, P13D1, P13D2, P13D3.





A

GO TO INTERNAL EEPROM MALFUNCTION CIRCUIT

B

C

2.CHECK ECM (FUEL TEMPERATURE SENSOR VOLTAGE)
2.CHECK ECM (FUEL TEMPERATURE SENSOR VOLTAGE)
a.
A302635C21
1.313,0.188 1.813,0.458 0.5,0.271 0.427,1.542 1.365,0.729 true 0.563,1.833 1.365,0.865 true 1.094,1.698 1.458,0.719 true 1.302,1.906 1.458,0.865 true 1.833,1.917 1.531,0.865 true 2.021,1.677 1.521,0.729 true 2.625,1.781 1.625,0.854 true 2.75,1.604 1.635,0.729 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.375,0.24 1.813,0.448 0.438,0.208 10 false C166 0.198,1.875 0.813,2.073 0.615,0.198 10 false 18 (VIJ1) 0.094,1.573 0.635,1.781 0.542,0.208 10 false 6 (EIJ1) 0.771,1.74 1.313,1.948 0.542,0.208 10 false 5 (EIJ2) 1.073,1.969 1.667,2.167 0.594,0.198 10 false 17 (VIJ2) 1.74,1.948 2.427,2.135 0.688,0.188 10 false 16 (VIJ3) 2.01,1.719 2.552,1.927 0.542,0.208 10 false 4 (EIJ3) 2.594,1.823 3.281,2.031 0.688,0.208 10 false 15 (VIJ4) 2.813,1.573 3.354,1.781 0.542,0.208 10 false 3 (EIJ4)
*a Component with harness connected
(ECM)


Disconnect the fuel pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C166-18 (VIJ1) - C166-6 (EIJ1) Ignition switch ON 4.5 to 5.5 V
C166-17 (VIJ2) - C166-5 (EIJ2) Ignition switch ON 4.5 to 5.5 V
C166-16 (VIJ3) - C166-4 (EIJ3) Ignition switch ON 4.5 to 5.5 V
C166-15 (VIJ4) - C166-3 (EIJ4) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)

NG

8.REPLACE ECM
3.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - ECM)
a.

Disconnect the injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C159-2 (VIJ1) - C166-18 (VIJ1) Always Below 1 Ω
C159-1 (EIJ1) - C166-6 (EIJ1) Always Below 1 Ω
C160-2 (VIJ2) - C166-17 (VIJ2) Always Below 1 Ω
C160-1 (EIJ2) - C166-5 (EIJ2) Always Below 1 Ω
C161-2 (VIJ3) - C166-16 (VIJ3) Always Below 1 Ω
C161-1 (EIJ3) - C166-4 (EIJ3) Always Below 1 Ω
C162-2 (VIJ4) - C166-15 (VIJ4) Always Below 1 Ω
C162-1 (EIJ4) - C166-3 (EIJ4) Always Below 1 Ω
C159-2 (VIJ1) or C166-18 (VIJ1) - Body ground Always 10 kΩ or higher
C159-1 (EIJ1) or C166-6 (EIJ1) - Body ground Always 10 kΩ or higher
C160-2 (VIJ2) or C166-17 (VIJ2) - Body ground Always 10 kΩ or higher
C160-1 (EIJ2) or C166-5 (EIJ2) - Body ground Always 10 kΩ or higher
C161-2 (VIJ3) or C166-16 (VIJ3) - Body ground Always 10 kΩ or higher
C161-1 (EIJ3) or C166-4 (EIJ3) - Body ground Always 10 kΩ or higher
C162-2 (VIJ4) or C166-15 (VIJ4) - Body ground Always 10 kΩ or higher
C162-1 (EIJ4) or C166-3 (EIJ4) - Body ground Always 10 kΩ or higher



d.

Reconnect the injector assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
a.

Replace the injector assembly of the cylinder relevant to the DTC.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

5.BLEED AIR FROM FUEL SYSTEM
5.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON for 8 seconds or more.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

f.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED