Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0120  Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction  P0121  Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem  P0122  Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input  P0123  Throttle / Pedal Position Sensor / Switch "A" Circuit High Input  P0220  Throttle / Pedal Position Sensor / Switch "B" Circuit  P0222  Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input  P0223  Throttle / Pedal Position Sensor / Switch "B" Circuit High Input  P2135  Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation  


DESCRIPTION

HINT:

These DTCs relate to the throttle position sensor.


The throttle position sensor is built into the throttle body with motor assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, each of which transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A297617
0.896,1.896 1.135,1.083 true 0.865,2.229 0.802,1.625 true 0.49,3.104 0.844,2.594 true 1.177,3.552 0.865,2.958 true 4.385,1.521 4.781,1.042 4.781,1.042 4.938,1.042 true 6.229,1.813 6.094,0.49 6.094,0.49 5.958,0.49 true 5.844,2.427 5.542,2.229 true 0.125,0.563 1.688,0.781 1.563,0.219 10 false Throttle Position Sensor 1.177,0.969 1.719,1.167 0.542,0.198 10 false Magnet 1.99,1.125 2.531,1.323 0.542,0.198 10 false ECM 0.292,1.51 0.854,1.708 0.563,0.198 10 false IC No. 1 0.292,3.125 0.854,3.323 0.563,0.198 10 false IC No. 2 1.25,3.49 2.167,3.688 0.917,0.198 10 false Magnet 1.302,1.74 1.917,1.938 0.615,0.198 10 false VCTA 1.302,2.073 1.917,2.271 0.615,0.198 10 false VTA1 1.313,2.427 1.927,2.625 0.615,0.198 10 false VTA2 1.323,2.76 1.781,2.958 0.458,0.198 10 false ETA 2.885,0.969 4.573,1.208 1.688,0.24 10 false Sensor Output Voltage (V) 4.333,0.417 6.063,0.656 1.729,0.24 10 false Line indicating VTA2 x 0.8 4.99,0.958 5.979,1.188 0.99,0.229 10 false Fail-safe Angle 5.917,2.396 6.396,2.594 0.479,0.198 10 false 1.11 V 4.563,1.885 5.042,2.083 0.479,0.198 10 false VTA2 4.896,2.729 5.375,2.927 0.479,0.198 10 false VTA1 3.969,1.458 4.198,1.646 0.229,0.188 10 false 5.0 3.906,1.677 4.208,1.865 0.302,0.188 10 false 4.65 3.802,2.229 4.24,2.417 0.438,0.188 10 false 2.58* 3.854,2.385 4.219,2.552 0.365,0.167 10 false 2.25 3.781,2.729 4.167,2.927 0.385,0.198 10 false 0.95* 3.844,2.896 4.229,3.094 0.385,0.198 10 false 0.69 4.302,3.115 4.688,3.313 0.385,0.198 10 false 6.5° 4.177,3.469 4.563,3.667 0.385,0.198 10 false 0° 6.5,3.469 6.74,3.656 0.24,0.188 10 false 84° 4.885,3.375 5.823,3.615 0.938,0.24 10 false Usable Range 5.021,3.833 6.99,4.167 1.969,0.333 10 false Throttle Valve Opening Angle (°) 4.594,4.24 6.563,4.573 1.969,0.333 10 false *: During fail-safe control 0.156,3.844 1.073,4.042 0.917,0.198 10 false Note: 0.156,4.042 3.396,4.448 3.24,0.406 10 false The throttle valve opening angle detected by the sensor terminal VTA1 is expressed as a percentage. 0.167,4.792 3.323,5.198 3.156,0.406 10 false Between 10% and 22%: Throttle valve fully closed 0.156,5.24 3.229,5.573 3.073,0.333 10 false Between 64% and 96%: Throttle valve fully open 0.156,5.646 3.229,5.979 3.073,0.333 10 false Approximately 18.2%: Fail-safe angle (6.5°) 3.698,4.677 5.938,4.969 2.24,0.292 10 false Characteristics of sensor output: 3.708,5.042 7.083,5.427 3.375,0.385 10 false The difference in voltage between VTA1 and VTA2 x 0.8 is approximately 1.11 V. 3.719,5.906 7.063,6.271 3.344,0.365 10 false (VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0120 Throttle / Pedal Position Sensor / Switch "A" Circuit Malfunction The output voltage of VTA1 quickly fluctuates beyond the upper and lower malfunction thresholds for 2 seconds or more (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored
P0121 Throttle / Pedal Position Sensor / Switch "A" Circuit Range / Performance Problem The difference between the VTA1 and VTA2 voltages is less than 0.8 V, or more than 1.6 V for 2 seconds (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


Comes on DTC stored
P0122 Throttle / Pedal Position Sensor / Switch "A" Circuit Low Input The output voltage of VTA1 is 0.2 V or less for 2 seconds or more (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input The output voltage of VTA1 is 4.54 V or higher for 2 seconds or more (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in E2 circuit

·

Short between VC and VTA1 circuit

·

ECM


Comes on DTC stored
P0220 Throttle / Pedal Position Sensor / Switch "B" Circuit The output voltage of VTA2 quickly fluctuates beyond the upper and lower malfunction thresholds for 2 seconds or more (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored
P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input The output voltage of VTA2 is 1.75 V or less for 2 seconds or more (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VC circuit

·

ECM


Comes on DTC stored
P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input The output voltage of VTA2 is 4.8 V or higher and VTA1 is between 0.2 V and 2.02 V for 2 seconds or more (1-trip detection logic).
·

Throttle position sensor (built into throttle body with motor assembly)

·

Open in VTA2 circuit

·

Open in E2 circuit

·

Short between VC and VTA2 circuit

·

ECM


Comes on DTC stored
P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation Either condition is met (1-trip detection logic):
(a) The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 0.5 seconds or more.
(b) The output voltage of VTA1 is 0.2 V or less and VTA2 is 1.75 V or less for 0.4 seconds or more.
·

Short between VTA1 and VTA2 circuits

·

Throttle position sensor (built into throttle body with motor assembly)

·

ECM


Comes on DTC stored

HINT:
·

When any of these DTCs are output, check the throttle valve opening angle using the intelligent tester.

Enter the following menus: Powertrain / Engine and ECT / Data List / ETCS / Throttle Position No.1 and Throttle Position No.2.

·

Throttle Position No.1 is the VTA1 signal, and Throttle Position No.2 is the VTA2 signal.



Reference (Normal Condition)
Tester Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Throttle Position No.1 0.5 to 1.1 V 3.2 to 4.8 V
Throttle Position No.2 2.1 to 3.1 V 4.6 to 5.0 V

FAIL-SAFE

When any of these DTCs as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A208237
0.125,2.948 0.552,3.188 0.427,0.24 10 false C67 0.125,3.135 4.604,3.51 4.479,0.375 10 false Throttle Position Sensor (Built into Throttle Body with Motor Assembly) 1.688,1.125 1.979,1.344 0.292,0.219 10 false VC 2.01,1.125 2.125,1.292 0.115,0.167 10 false 5 5.333,1.125 5.583,1.365 0.25,0.24 10 false 10 6,2.979 6.438,3.26 0.438,0.281 10 false C95 1.625,0.583 2.01,0.813 0.385,0.229 10 false VTA 2.01,0.583 2.125,0.75 0.115,0.167 10 false 6 5.406,1.677 5.563,1.854 0.156,0.177 10 false 4 5.406,0.583 5.583,0.76 0.177,0.177 10 false 3 1.531,1.677 2.031,1.969 0.5,0.292 10 false VTA2 2.01,1.677 2.125,1.844 0.115,0.167 10 false 4 1.688,2.26 1.979,2.563 0.292,0.302 10 false E2 2.01,2.26 2.125,2.427 0.115,0.167 10 false 3 5.406,2.26 5.563,2.438 0.156,0.177 10 false 9 6,3.156 6.427,3.427 0.427,0.271 10 false ECM 5.573,1.125 6.052,1.417 0.479,0.292 10 false VCTA 5.583,0.573 6.042,0.854 0.458,0.281 10 false VTA1 5.583,1.677 6.052,1.917 0.469,0.24 10 false VTA2 5.583,2.26 6.01,2.531 0.427,0.271 10 false ETA 1.125,0.813 1.385,1.063 0.26,0.25 10 false IC 1.125,1.698 1.385,1.927 0.26,0.229 10 false IC

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (THROTTLE POSITION NO. 1 AND THROTTLE POSITION NO. 2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Position No. 1 and Throttle Position No. 2.

Powertrain > Engine and ECT > Data List
Tester Display
Throttle Position No.1
Throttle Position No.2
50003 234 282,283

d.

Read the values displayed on the tester.

Result:
Throttle Position No. 1 (VTA1) when Accelerator Pedal Released Throttle Position No. 2 (VTA2) when Accelerator Pedal Released Throttle Position No. 1 (VTA1) when Accelerator Pedal Depressed Throttle Position No. 2 (VTA2) when Accelerator Pedal Depressed Trouble Area Proceed to
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VC circuit open A
4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V E2 circuit open
0 V to 0.2 V, or 4.5 V to 5.0 V 2.1 to 3.1 V
(Fail-safe)
0 V to 0.2 V, or 4.5 V to 5.0 V 2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or short to ground
0.6 to 1.4 V
(Fail-safe)
0 V to 0.2 V, or 4.5 V to 5.0 V 0.6 to 1.4 V
(Fail-safe)
0 V to 0.2 V, or 4.5 V to 5.0 V VTA2 circuit open or short to ground
0.5 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 5.0 V
(Not fail-safe)
Throttle position sensor circuit normal B


HINT:
·

DTC P0121/41 is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is output. Use the following formula to confirm the relative differences in voltage.

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position No. 1

VTA2: Throttle Position No. 2


·

If DTC P0121 is output, proceed to "Check Harness and Connector (Throttle Position Sensor - ECM)".





A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C67-5 (VC) - C95-10 (VCTA) Always Below 1 Ω
C67-6 (VTA) - C95-3 (VTA1) Always Below 1 Ω
C67-4 (VTA2) - C95-4 (VTA2) Always Below 1 Ω
C67-3 (E2) - C95-9 (ETA) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C67-5 (VC) or C95-10 (VCTA) - Body ground Always 10 kΩ or higher
C67-6 (VTA) or C95-3 (VTA1) - Body ground Always 10 kΩ or higher
C67-4 (VTA2) or C95-4 (VTA2) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle body with motor assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE POSITION SENSOR - ECM)

3.INSPECT ECM (VC VOLTAGE)
a.
A200902
0.604,0.948 0.948,1.198 0.344,0.25 1.479,1.583 1.646,1.125 true 2.063,1.573 1.927,1.125 true 0.125,0.094 0.438,0.323 0.313,0.229 10 false *a 0.656,1 1.125,1.25 0.469,0.25 10 false C67 1.385,1.594 1.854,1.844 0.469,0.25 10 false E2 1.99,1.594 2.458,1.844 0.469,0.25 10 false VC
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


Disconnect the throttle body with motor assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C67-5 (VC) - C67-3 (E2) Ignition switch ON 4.5 to 5.5 V



c.

Reconnect the throttle body with motor assembly connector.


Result:
Proceed to
OK
NG



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>THROTTLE BODY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine.


f.

Allow the engine to idle for 15 seconds or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC P0120, P0121, P0122, P0123, P0220, P0222, P0223 and/or P2135 is output A
DTC is not output B




A

B

END