Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM J

2TR-FBE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate the detection of vehicle malfunctions by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually; when the ignition switch is first turned to ON, the MIL turns on and then off. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A242470
5.979,0.844 6.24,1.031 0.26,0.188 10 false W 1.25,0.844 1.719,1.042 0.469,0.198 10 false AM2 0.552,1.927 1.073,2.177 0.521,0.25 10 false AM2 6.271,2.917 6.688,3.146 0.417,0.229 10 false ECM 1.063,0.792 1.208,0.969 0.146,0.177 10 false 5 2.26,0.792 2.427,0.938 0.167,0.146 10 false 6 0.677,2.75 1.333,3.021 0.656,0.271 10 false Battery 3.677,1.563 5.594,1.844 1.917,0.281 10 false Combination Meter Assembly 2.875,1.094 3.313,1.333 0.438,0.24 10 false MET 1.906,0.844 2.24,1.031 0.333,0.188 10 false IG2 4.885,0.833 5.115,1.01 0.229,0.177 10 false 39 3.76,0.833 3.938,0.979 0.177,0.146 10 false 21 3.677,1.417 4.125,1.646 0.448,0.229 10 false G19 5.74,0.844 6.031,1.031 0.292,0.188 10 false 13 6.26,2.75 6.719,2.938 0.458,0.188 10 false G145 0.917,1.375 2.635,1.615 1.719,0.24 10 false Ignition Switch Assembly 0.917,1.219 1.385,1.417 0.469,0.198 10 false G9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Turn the ignition switch to ON.


b.

Check the illumination condition of the MIL.

Result:
Condition Proceed to
MIL remains illuminated (Even after ignition switch turned to ON and several seconds have passed, MIL still remains illuminated) A
MIL remains off (Does not illuminate at all) B
MIL illuminates for several seconds, but turns off after engine is started C




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT ENGINE STARTS

C

SYSTEM OK

2.CHECK WHETHER MIL TURNS OFF
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Check if any DTCs are output. Note down any DTCs.


f.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

g.

Check if the MIL goes off.

OK:

MIL goes off.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G19-39 (CHK) or G145-13 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the combination meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)

5.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Check that the engine starts.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The intelligent tester cannot communicate with the ECM.




A

6.CHECK COMBINATION METER ASSEMBLY

B

6.CHECK COMBINATION METER ASSEMBLY
a.
A262769
0.292,0.229 0.646,0.458 0.354,0.229 0.51,1.5 0.573,0.938 true 0.094,0.063 0.365,0.323 0.271,0.26 10 false *a 0.313,0.271 0.781,0.563 0.469,0.292 10 false G145 0.396,1.542 0.865,1.833 0.469,0.292 10 false 13 (W)
*a Component with harness connected
(ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G145-13 (W) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-39 (CHK) - G145-13 (W) Always Below 1 Ω



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)