Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM J

2TR-FBE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power supply voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A206916
4.375,1.125 6.313,1.438 1.938,0.313 10 false 5 V Constant Voltage Circuit 5.354,1.979 6.469,2.26 1.115,0.281 10 false Microprocessor 1.698,1.125 2.792,1.375 1.094,0.25 10 false from EFI Fuse 1.542,1.469 2.781,1.719 1.24,0.25 10 false from MAIN Relay 2.938,1.01 3.458,1.229 0.521,0.219 10 false BATT 0.313,2.188 2.635,2.729 2.323,0.542 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have ICs) 0.313,3.021 2.677,3.448 2.365,0.427 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.083,3.125 4.344,3.333 0.26,0.208 10 false R 3,1.354 3.281,1.552 0.281,0.198 10 false +B 2.729,2.021 3.677,2.385 0.948,0.365 10 false VCTA, VCPA, VCP2 4.938,3.354 5.385,3.583 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON, and then goes off when the engine starts.


WIRING DIAGRAM

A262786
0.771,2.604 1.292,2.896 0.521,0.292 10 false C67 0.771,2.76 2.583,3.094 1.813,0.333 10 false Throttle Position Sensor 2.229,0.854 2.573,1.052 0.344,0.198 10 false VC 2.229,2.177 2.594,2.417 0.365,0.24 10 false E2 2.135,1.292 2.5,1.51 0.365,0.219 10 false VTA 2.104,4.563 2.583,4.771 0.479,0.208 10 false VPA 2.115,5.406 2.531,5.635 0.417,0.229 10 false EP1 2.063,1.74 2.656,2.021 0.594,0.281 10 false VTA2 5.01,0.75 5.5,1 0.49,0.25 10 false VCTA 5.01,2.073 5.448,2.281 0.438,0.208 10 false ETA 5.01,3.615 5.531,3.844 0.521,0.229 10 false VCPA 5.01,1.292 5.448,1.49 0.438,0.198 10 false VTA1 5.01,1.74 5.49,1.969 0.479,0.229 10 false VTA2 5.01,4.031 5.51,4.25 0.5,0.219 10 false VCP2 5.01,4.573 5.438,4.792 0.427,0.219 10 false VPA 5.01,5.313 5.406,5.521 0.396,0.208 10 false EPA 5.01,4.99 5.5,5.229 0.49,0.24 10 false VPA2 5.01,5.729 5.521,5.99 0.51,0.26 10 false EPA2 0.74,6.302 1.167,6.604 0.427,0.302 10 false G6 0.74,6.458 2.938,6.729 2.198,0.271 10 false Accelerator Pedal Position Sensor 2.021,3.719 2.594,3.979 0.573,0.26 10 false VCPA 2.021,4.135 2.531,4.365 0.51,0.229 10 false VCP2 2.021,4.99 2.573,5.208 0.552,0.219 10 false VPA2 2.115,5.833 2.573,6.083 0.458,0.25 10 false EP2 4.625,0.854 5.01,1.083 0.385,0.229 10 false C95 4.625,1.302 5.01,1.531 0.385,0.229 10 false C95 4.625,1.74 5,1.969 0.375,0.229 10 false C95 4.615,2.177 4.969,2.406 0.354,0.229 10 false C95 4.708,1.542 4.99,1.802 0.281,0.26 10 false 4 4.708,1.094 4.917,1.302 0.208,0.208 10 false 3 4.667,0.646 4.917,0.854 0.25,0.208 10 false 10 4.698,1.979 4.917,2.229 0.219,0.25 10 false 9 4.573,3.719 5.01,3.958 0.438,0.24 10 false G146 4.573,4.156 5.031,4.365 0.458,0.208 10 false G146 4.583,4.573 4.99,4.792 0.406,0.219 10 false G146 4.573,4.99 5.021,5.229 0.448,0.24 10 false G146 4.573,5.417 5.052,5.646 0.479,0.229 10 false G146 4.583,5.833 5.063,6.083 0.479,0.25 10 false G146 4.719,3.521 4.927,3.719 0.208,0.198 10 false 4 4.708,4.802 4.979,5.063 0.271,0.26 10 false 5 4.708,4.396 4.948,4.604 0.24,0.208 10 false 6 4.698,5.646 4.948,5.896 0.25,0.25 10 false 1 4.708,5.219 4.958,5.406 0.25,0.188 10 false 2 4.708,3.969 4.938,4.167 0.229,0.198 10 false 3 2.542,0.75 2.719,0.969 0.177,0.219 10 false 5 2.542,1.208 2.781,1.406 0.24,0.198 10 false 6 2.542,1.635 2.781,1.865 0.24,0.229 10 false 4 2.542,2.083 2.74,2.281 0.198,0.198 10 false 3 2.542,3.615 2.76,3.813 0.219,0.198 10 false 4 2.542,4.052 2.75,4.24 0.208,0.188 10 false 1 2.542,4.469 2.781,4.75 0.24,0.281 10 false 6 2.542,4.875 2.719,5.094 0.177,0.219 10 false 3 2.542,5.292 2.719,5.583 0.177,0.292 10 false 5 2.542,5.74 2.74,5.99 0.198,0.25 10 false 2 5.594,6.823 6.073,7.094 0.479,0.271 10 false ECM

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

SYSTEM OK

NG

2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
2.CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Check the communication between the tester and ECM.

Result:
Result Proceed to
Communication is possible A
Communication is not possible B




A

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the throttle body with motor assembly connector.



A

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE POSITION SENSOR)

B

4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
4.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the accelerator pedal rod assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the accelerator pedal rod assembly connector.



A

REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (ACCELERATOR PEDAL POSITION SENSOR)

B

5.CHECK HARNESS AND CONNECTOR
5.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the accelerator pedal rod assembly connector.


c.

Disconnect the ECM connectors.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C95-10 (VCTA) - Body ground Always 10 kΩ or higher
G146-4 (VCPA) - Body ground Always 10 kΩ or higher
G146-3 (VCP2) - Body ground Always 10 kΩ or higher



e.

Reconnect the throttle body with motor assembly connector.


f.

Reconnect the accelerator pedal rod assembly connector.


g.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR