Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve. The ECM uses this information to determine the fuel injection time and to provide the appropriate air fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the air flow through the sensor and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When any of these DTCs are stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM, according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.


A094565
1.833,1.656 1.302,0.552 false 2.333,1.094 2.135,1.563 false 4.615,1.365 3.906,1.813 3.906,1.813 3.906,2.021 false 4.938,1.656 5.271,2.094 5.271,2.094 5.271,2.344 false 0.031,0.479 1.365,0.927 1.333,0.448 10 false Temperature Sensor (Thermistor) 3.458,2.031 4.781,2.438 1.323,0.406 10 false Temperature Sensor (Thermistor) 2.042,0.198 2.438,0.479 0.396,0.281 10 false B+ 2.177,0.646 3.354,0.896 1.177,0.25 10 false Power Transistor 2.375,1 3.542,1.438 1.167,0.438 10 false Platinum Hot Wire (Heater) 4.885,2.365 6.594,2.677 1.708,0.313 10 false Platinum Hot Wire (Heater) 1.573,1.594 1.708,1.792 0.135,0.198 10 false A 2.365,1.583 2.5,1.781 0.135,0.198 10 false B 2.813,1.677 3.365,2.094 0.552,0.417 10 false Output Voltage

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0102 Mass or Volume Air Flow Circuit Low Input The mass air flow meter voltage is below 0.2 V for 3 seconds (1-trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored
P0103 Mass or Volume Air Flow Circuit High Input The mass air flow meter voltage is higher than 4.9 V for 3 seconds (1-trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the air flow rate using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Mass Air Flow Rate (g/ms) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


160.0 or more
·

Open in E2G circuit




WIRING DIAGRAM

A262767
0.625,3.719 1.156,3.938 0.531,0.219 10 false Battery 0.75,0.885 1.021,1.104 0.271,0.219 10 false 1H 1.208,1.01 1.583,1.177 0.375,0.167 10 false EFI 1.625,1.865 2.802,2.146 1.177,0.281 10 false Integration Relay 0.802,0.698 0.979,0.865 0.177,0.167 10 false 1 2.521,0.885 2.833,1.115 0.313,0.229 10 false 1J 4.781,1.094 5.125,1.313 0.344,0.219 10 false VG 5.76,1.083 6.073,1.333 0.313,0.25 10 false VG 5.438,1 5.719,1.281 0.281,0.281 10 false 13 5.406,1.198 5.823,1.438 0.417,0.24 10 false C95 5.469,1.5 5.667,1.667 0.198,0.167 10 false 7 5.406,1.698 5.813,1.927 0.406,0.229 10 false C95 5.083,1.281 5.219,1.448 0.135,0.167 10 false 3 4.698,1.594 5.083,1.813 0.385,0.219 10 false E2G 5.76,1.583 6.146,1.802 0.385,0.219 10 false E2G 5.448,2.781 5.677,2.969 0.229,0.188 10 false 12 5.354,2.969 5.833,3.24 0.479,0.271 10 false G146 5.76,2.865 6.292,3.094 0.531,0.229 10 false MREL 3.833,2.094 4.26,2.323 0.427,0.229 10 false C36 3.833,2.26 5.24,2.563 1.406,0.302 10 false Mass Air Flow Meter 5.083,1.781 5.219,1.948 0.135,0.167 10 false 2 3.865,0.771 4.198,0.969 0.333,0.198 10 false +B 1.365,1.656 1.615,1.875 0.25,0.219 10 false 1J 2.552,1.063 2.698,1.229 0.146,0.167 10 false 2 2.552,0.698 2.729,0.865 0.177,0.167 10 false 5 2.521,1.229 2.75,1.469 0.229,0.24 10 false 1J 1.156,1.646 1.333,1.813 0.177,0.167 10 false 3 3.667,0.771 3.844,0.938 0.177,0.167 10 false 1 6.188,3.469 6.615,3.698 0.427,0.229 10 false ECM 1.813,1.583 2.302,1.813 0.49,0.229 10 false MAIN 0.458,2.656 1.156,2.906 0.698,0.25 10 false BATT P/I

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the values displayed on the tester.

Result:
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B




A

2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER (POWER SOURCE VOLTAGE)
a.
A242722
0.26,1.073 0.615,1.302 0.354,0.229 1.76,1.896 1.188,1.271 true 0.115,0.073 0.542,0.438 0.427,0.365 10 false *a 0.313,1.104 0.74,1.469 0.427,0.365 10 false C36 1.792,1.854 2.188,2.073 0.396,0.219 10 false +B
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (+B) - Body ground Ignition switch ON 11 to 14 V



c.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY [MAIN RELAY])
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C36-3 (VG) - C95-13 (VG) Always Below 1 Ω
C36-2 (E2G) - C95-7 (E2G) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C36-3 (VG) or C95-13 (VG) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

4.CHECK MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>MASS AIR FLOW METER>INSPECTION


c.

Inspect the function of the mass air flow meter.

i.

Connect the Techstream to the DLC3.


ii.

Turn the ignition switch to ON.


iii.

Turn the Techstream on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.

Powertrain > Engine and ECT > Data List
Tester Display
MAF
50003 234 3

v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.




Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.
A242722
0.198,1.052 0.552,1.281 0.354,0.229 1.688,1.823 1.448,1.292 true 0.156,0.115 0.521,0.375 0.365,0.26 10 false *a 0.26,1.094 0.625,1.354 0.365,0.26 10 false C36 1.74,1.76 2.104,2.021 0.365,0.26 10 false E2G
*a Front view of wire harness connector
(to Mass Air Flow Meter)


Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-2 (E2G) - Body ground Always Below 1 Ω



c.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

REPLACE MASS AIR FLOW METER

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C36-2 (E2G) - C95-7 (E2G) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C36-2 (E2G) or C95-7 (E2G) - Body ground Always 10 kΩ or higher



d.

Reconnect the mass air flow meter connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY [MAIN RELAY])
a.

Disconnect the mass air flow meter connector.


b.

Remove the integration relay (MAIN relay) from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C36-1 (+B) - 1J-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C36-1 (+B) or 1J-5 - Body ground Always 10 kΩ or higher



d.

Reinstall the integration relay.


e.

Reconnect the mass air flow meter connector.


Result:
Proceed to
OK
NG



OK

REPLACE INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - INTEGRATION RELAY [MAIN RELAY])