Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor consists of a magnet and an iron core which is wrapped with copper wire, and is installed to the cylinder head. When the camshaft rotates, each of the 3 teeth on the camshaft passes by the camshaft position sensor. This activates the internal magnet in the sensor, generating a voltage in the copper wire. The camshaft rotation is synchronized with the crankshaft rotation. When the crankshaft turns twice, the voltage is generated 3 times in the camshaft position sensor. The generated voltage in the sensor acts as a signal, allowing the ECM to determine the camshaft position. This signal is then used to control the ignition timing, fuel injection timing and VVT system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) Either condition is met:
·

Camshaft/crankshaft misalignment is detected at an engine speed of 600 rpm or more (1 trip detection logic).

·

No VVT sensor signal is sent to the ECM during cranking (2 trip detection logic).


·

Open or short in sensor circuit

·

Camshaft position sensor

·

Camshaft

·

Timing chain has jumped tooth

·

ECM


Comes on DTC stored

HINT:

DTC P0340 indicates a malfunction relating to the camshaft position sensor circuit (the wire harness between the ECM and camshaft position sensor, and the camshaft position sensor itself).


Reference: Inspection using an oscilloscope

A063955N10
2.792,0.594 3.135,0.906 0.344,0.313 10 false GND 2.802,1.406 3.146,1.719 0.344,0.313 10 false GND 0.042,0.042 0.656,0.24 0.615,0.198 10 false 5 V/DIV. 0.094,0.604 0.49,0.792 0.396,0.188 10 false CH1 0.094,1.385 0.479,1.573 0.385,0.188 10 false CH2 1.521,1.917 2.563,2.135 1.042,0.219 10 false 20 msec./DIV.

HINT:
·

The correct waveforms are as shown in the illustration.

·

G2+ is the camshaft position sensor signal, and NE+ is the crankshaft position sensor signal.

·

Grounding failure of the shielded wire may cause noise in the waveforms.


Item Contents
ECM Terminal Name CH1: G2 - NE-
CH2: NE+ - NE-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Cranking or idling


WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT CAMSHAFT POSITION SENSOR (RESISTANCE)

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C68-1 - C96-11 Always Below 1 Ω
C68-2 - C96-5 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C68-1 or C96-11 - Body ground Always 10 kΩ or higher
C68-2 or C96-5 - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the camshaft position sensor connector.


Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
A302550E01
0.49,1.729 0.802,1.927 0.313,0.198 10 false OK 2.667,1.833 2.979,2.031 0.313,0.198 10 false NG 1.667,1.573 2.49,1.833 0.823,0.26 10 false Clearance

Check the camshaft position sensor installation condition.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK VALVE TIMING

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

4.CHECK VALVE TIMING
a.

Check the valve timing.

HINT:

There are no marks on the cylinder head to match-up for the purpose of checking valve timing. Valve timing can only be inspected by lining up the colored plates on the timing chain with the marks on the pulleys. It may be necessary to remove and re-install the chain to match-up the timing marks.

Click hereEngine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY



Result:
Proceed to
OK
NG



OK

5.INSPECT CAMSHAFT

NG

ADJUST VALVE TIMING

5.INSPECT CAMSHAFT
a.

Check the teeth of the camshaft.

OK:

Camshaft teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE CAMSHAFT POSITION SENSOR

NG

6.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

f.

Read DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0340 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B