Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle to enhance ignition accuracy and suppress high voltage losses.

The DIS is an ignition system in which each cylinder is ignited by one ignition coil assembly. The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Based on the IGT signals, the ECM turns the power transistor inside the igniter on and off, turning the current to the primary coil on and off. When the current to the primary coil is cut off, a voltage is generated in the secondary coil and then applied to the spark plugs, causing them to spark inside the cylinders. At the same time, the igniter sends back the ignition confirmation (IGF) signal to the ECM.

A210600
5.396,1.146 5.833,0.854 false 4.406,1.375 4.188,0.844 false 4.188,0.844 4.01,0.844 false 0.302,1.417 2.188,1.677 1.885,0.26 10 false Crankshaft Position Sensor 0.333,3.188 2.167,3.479 1.833,0.292 10 false Camshaft Position Sensor 0.208,4.313 2.125,5.146 1.917,0.833 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 1.49,6.396 2.542,6.604 1.052,0.208 10 false to Tachometer 2.719,5.688 3.24,5.927 0.521,0.24 10 false TACH 2.74,0.656 3.281,0.958 0.542,0.302 10 false ECM 2.854,1.448 3.313,1.656 0.458,0.208 10 false IGT1 2.854,1.75 3.438,2.031 0.583,0.281 10 false IGF1 2.854,2.74 3.292,2.99 0.438,0.25 10 false IGT2 2.854,4.094 3.198,4.344 0.344,0.25 10 false IGT3 2.854,5.417 3.26,5.625 0.406,0.208 10 false IGT4 4.563,0.521 5.448,0.792 0.885,0.271 10 false from Battery 3.594,0.76 4.042,0.938 0.448,0.177 10 false Igniter 5.875,0.771 7.052,1.188 1.177,0.417 10 false No. 1 Ignition Coil Assembly 5.615,1.865 6.802,2.135 1.188,0.271 10 false No. 1 Spark Plug 5.615,3.073 6.781,3.292 1.167,0.219 10 false No. 2 Spark Plug 5.615,4.396 6.823,4.656 1.208,0.26 10 false No. 3 Spark Plug 5.615,5.698 6.792,5.958 1.177,0.26 10 false No. 4 Spark Plug 4.198,2.625 5.375,3.01 1.177,0.385 10 false No. 2 Ignition Coil Assembly 4.198,5.271 5.375,5.656 1.177,0.385 10 false No. 4 Ignition Coil Assembly 4.198,3.948 5.375,4.333 1.177,0.385 10 false No. 3 Ignition Coil Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT 1 circuit between ignition coil and ECM

·

No. 1 ignition coil assembly

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT 2 circuit between ignition coil and ECM

·

No. 2 ignition coil assembly

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT 3 circuit between ignition coil and ECM

·

No. 3 ignition coil assembly

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT 4 circuit between ignition coil and ECM

·

No. 4 ignition coil assembly

·

ECM


Comes on DTC stored

WIRING DIAGRAM

A242348
3.427,1.702 3.699,1.883 0.272,0.182 10 C70 3.429,1.87 5.286,2.052 1.857,0.182 10 No. 1 Ignition Coil Assembly 3.433,7.131 5.338,7.312 1.905,0.182 10 No. 4 Ignition Coil Assembly 3.409,5.386 5.404,5.567 1.996,0.182 10 No. 3 Ignition Coil Assembly 3.415,3.607 5.327,3.789 1.912,0.182 10 No. 2 Ignition Coil Assembly 3.434,6.979 3.706,7.161 0.272,0.182 10 C73 3.406,5.226 3.678,5.408 0.272,0.182 10 C72 3.415,3.453 3.687,3.635 0.272,0.182 10 C71 3.274,0.67 3.43,0.851 0.156,0.182 10 1 3.282,1.258 3.439,1.44 0.156,0.182 10 4 5.195,0.668 5.351,0.85 0.156,0.182 10 3 5.192,1.255 5.348,1.436 0.156,0.182 10 2 3.278,5.956 3.435,6.138 0.156,0.182 10 1 3.287,6.545 3.443,6.726 0.156,0.182 10 4 5.2,5.955 5.356,6.137 0.156,0.182 10 3 5.197,6.541 5.353,6.723 0.156,0.182 10 2 3.288,4.191 3.444,4.373 0.156,0.182 10 1 3.296,4.779 3.453,4.961 0.156,0.182 10 4 5.209,4.19 5.365,4.371 0.156,0.182 10 3 5.206,4.776 5.362,4.958 0.156,0.182 10 2 3.278,2.445 3.435,2.627 0.156,0.182 10 1 3.287,3.034 3.443,3.215 0.156,0.182 10 4 5.2,2.444 5.356,2.625 0.156,0.182 10 3 5.197,3.03 5.353,3.212 0.156,0.182 10 2 6.299,8.122 6.625,8.303 0.326,0.182 10 ECM 6.299,7.97 6.673,8.152 0.374,0.182 10 C98 5.884,0.668 6.194,0.85 0.31,0.182 10 1 5.884,2.433 6.185,2.615 0.301,0.182 10 2 5.884,4.19 6.149,4.371 0.264,0.182 10 3 5.884,5.932 6.185,6.113 0.301,0.182 10 4 5.813,6.524 5.985,6.705 0.172,0.182 10 10 5.884,7.337 6.133,7.518 0.249,0.182 10 5 6.121,0.766 6.447,0.948 0.326,0.182 10 IGT1 6.128,2.536 6.454,2.717 0.326,0.182 10 IGT2 6.124,4.291 6.45,4.473 0.326,0.182 10 IGT3 6.14,6.046 6.466,6.227 0.326,0.182 10 IGT4 6.13,6.634 6.456,6.816 0.326,0.182 10 IGF1 6.155,7.449 6.343,7.63 0.187,0.182 10 E1 1.961,6.959 2.117,7.14 0.156,0.182 10 1 2.118,7.144 2.391,7.326 0.272,0.182 10 C79 2.112,7.325 2.918,7.672 0.806,0.346 10 Noise Filter (Ignition) 3.523,0.776 3.715,0.958 0.191,0.182 10 +B 4.738,0.788 5.064,0.969 0.326,0.182 10 IGT1 3.519,1.366 3.845,1.547 0.326,0.182 10 GND 4.806,1.369 5.054,1.55 0.249,0.182 10 IGF 3.523,6.048 3.715,6.229 0.191,0.182 10 +B 4.738,6.059 5.064,6.241 0.326,0.182 10 IGT4 3.519,6.637 3.845,6.819 0.326,0.182 10 GND 4.806,6.64 5.054,6.822 0.249,0.182 10 IGF 3.523,2.521 3.715,2.702 0.191,0.182 10 +B 4.738,2.533 5.064,2.714 0.326,0.182 10 IGT2 3.519,3.11 3.845,3.292 0.326,0.182 10 GND 4.806,3.113 5.054,3.295 0.249,0.182 10 IGF 3.527,4.299 3.718,4.48 0.191,0.182 10 +B 4.742,4.311 5.068,4.492 0.326,0.182 10 IGT3 3.522,4.888 3.848,5.07 0.326,0.182 10 GND 4.809,4.891 5.058,5.073 0.249,0.182 10 IGF 0.632,7.69 1.187,7.883 0.556,0.193 10 Battery 0.524,5.99 0.941,6.183 0.417,0.193 10 AM2 0.602,1.188 0.874,1.37 0.272,0.182 10 G9 0.604,1.356 2.46,1.538 1.857,0.182 10 Ignition Switch Assembly 0.626,0.668 0.782,0.85 0.156,0.182 10 5 1.819,0.668 1.975,0.85 0.156,0.182 10 6 0.819,0.668 1.186,0.85 0.367,0.182 10 AM2 1.474,0.668 1.8,0.85 0.326,0.182 10 IG2 2.098,0.937 2.515,1.13 0.417,0.193 10 INJ

CAUTION / NOTICE / HINT

HINT:
·

The following inspection procedure is for the No. 1 cylinder. If any of the other cylinders are malfunctioning, inspect their circuits by referring to the following procedure.

·

If DTC P0351 is output, check the ignition coil assembly No. 1 circuit.

·

If DTC P0352 is output, check the ignition coil assembly No. 2 circuit.

·

If DTC P0353 is output, check the ignition coil assembly No. 3 circuit.

·

If DTC P0354 is output, check the ignition coil assembly No. 4 circuit.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0351, P0352, P0353 or P0354 is output A
DTC P0351, P0352, P0353 and P0354 are output B




A

2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

B

6.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Perform a simulation test.


g.

Check the DTCs output to the tester.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
Same DTC output A
Different ignition coil assembly DTC output B




A

3.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)

B

3.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
A200905
0.448,0.49 0.813,0.719 0.365,0.229 0.448,0.781 0.813,1.01 0.365,0.229 0.448,1.073 0.813,1.302 0.365,0.229 0.448,1.365 0.813,1.594 0.365,0.229 1.365,1.625 1.365,1.198 true 2.031,1.646 2.031,1.198 true 0.073,0.042 0.385,0.271 0.313,0.229 10 false *a 0.51,0.531 0.823,0.76 0.313,0.229 10 false C70 0.5,0.823 0.813,1.052 0.313,0.229 10 false C71 0.5,1.115 0.813,1.344 0.313,0.229 10 false C72 0.5,1.406 0.813,1.635 0.313,0.229 10 false C73 1.271,1.667 1.583,1.896 0.313,0.229 10 false +B 1.906,1.667 2.354,1.917 0.448,0.25 10 false GND
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C70-1 (+B) - C70-4 (GND) Ignition switch ON 11 to 14 V
C71-1 (+B) - C71-4 (GND) Ignition switch ON 11 to 14 V
C72-1 (+B) - C72-4 (GND) Ignition switch ON 11 to 14 V
C73-1 (+B) - C73-4 (GND) Ignition switch ON 11 to 14 V



c.

Reconnect the ignition coil assembly connectors.


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C70-2 (IGF) - C98-10 (IGF1) Always Below 1 Ω
C71-2 (IGF) - C98-10 (IGF1) Always Below 1 Ω
C72-2 (IGF) - C98-10 (IGF1) Always Below 1 Ω
C73-2 (IGF) - C98-10 (IGF1) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C70-2 (IGF) or C98-10 (IGF1) - Body ground Always 10 kΩ or higher
C71-2 (IGF) or C98-10 (IGF1) - Body ground Always 10 kΩ or higher
C72-2 (IGF) or C98-10 (IGF1) - Body ground Always 10 kΩ or higher
C73-2 (IGF) or C98-10 (IGF1) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the ignition coil assembly connectors.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

5.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C70-3 (IGT1) - C98-1 (IGT1) Always Below 1 Ω
C71-3 (IGT2) - C98-2 (IGT2) Always Below 1 Ω
C72-3 (IGT3) - C98-3 (IGT3) Always Below 1 Ω
C73-3 (IGT4) - C98-4 (IGT4) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C70-3 (IGT1) or C98-1 (IGT1) - Body ground Always 10 kΩ or higher
C71-3 (IGT2) or C98-2 (IGT2) - Body ground Always 10 kΩ or higher
C72-3 (IGT3) or C98-3 (IGT3) - Body ground Always 10 kΩ or higher
C73-3 (IGT4) or C98-4 (IGT4) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the ignition coil assembly connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

6.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C70-4 (GND) - Body ground Always Below 1 Ω
C71-4 (GND) - Body ground Always Below 1 Ω
C72-4 (GND) - Body ground Always Below 1 Ω
C73-4 (GND) - Body ground Always Below 1 Ω



c.

Reconnect the ignition coil assembly connectors.


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

7.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH ASSEMBLY)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ignition switch assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C70-1 (+B) - G9-6 (IG2) Always Below 1 Ω
C71-1 (+B) - G9-6 (IG2) Always Below 1 Ω
C72-1 (+B) - G9-6 (IG2) Always Below 1 Ω
C73-1 (+B) - G9-6 (IG2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C70-1 (+B) or G9-6 (IG2) - Body ground Always 10 kΩ or higher
C71-1 (+B) or G9-6 (IG2) - Body ground Always 10 kΩ or higher
C72-1 (+B) or G9-6 (IG2) - Body ground Always 10 kΩ or higher
C73-1 (+B) or G9-6 (IG2) - Body ground Always 10 kΩ or higher



d.

Reconnect the ignition switch assembly connectors.


e.

Reconnect the ignition coil assembly connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IGNITION SWITCH ASSEMBLY)