Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is built into the throttle body. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2102 Throttle Actuator Control Motor Circuit Low Both conditions are met for 2.0 seconds (1 trip detection logic):
(a) The throttle actuator duty ratio is 80% or more.
(b) The throttle actuator current is 0.5 A or less.
·

Open in throttle actuator circuit

·

Throttle body with motor assembly

·

ECM


Comes on DTC stored
P2103 Throttle Actuator Control Motor Circuit High Either condition is met (1 trip detection logic):
·

The throttle actuator current is 10 A or higher for 0.1 seconds.

·

The throttle actuator current is 7 A or higher for 0.6 seconds.


·

Short in throttle actuator circuit

·

Throttle body with motor assembly

·

ECM


Comes on DTC stored

FAIL-SAFE

When either of these DTCs as well as other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator and the throttle valve is returned to a 6.5° opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing in accordance with the accelerator pedal position to allow the vehicle to continue at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly. The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A226209
0.063,2.51 0.438,2.75 0.375,0.24 10 false C67 0.052,2.698 2.26,3.01 2.208,0.313 10 false Throttle Body with Motor Assembly 2.74,2.594 3.438,2.854 0.698,0.26 10 false Shielded 1.135,1.146 1.427,1.365 0.292,0.219 10 false M+ 1.156,1.875 1.448,2.104 0.292,0.229 10 false M- 1.448,1.146 1.604,1.323 0.156,0.177 10 false 2 1.448,1.875 1.604,2.052 0.156,0.177 10 false 1 5.802,3.313 6.333,3.51 0.531,0.198 10 false ECM 4.594,1.052 4.844,1.229 0.25,0.177 10 false 14 4.594,1.802 4.896,2.063 0.302,0.26 10 false 15 4.604,2.563 4.833,2.74 0.229,0.177 10 false 24 4.896,1.156 5.219,1.438 0.323,0.281 10 false M+ 4.906,1.896 5.177,2.115 0.271,0.219 10 false M- 4.896,2.75 5.427,3.021 0.531,0.271 10 false GE01 5.354,1.271 6.51,1.74 1.156,0.469 10 false Throttle Actuator Control Circuit 4.552,1.25 4.927,1.479 0.375,0.229 10 false C98 4.542,2 4.969,2.271 0.427,0.271 10 false C98 4.542,2.76 4.865,2.938 0.323,0.177 10 false C97

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the intelligent tester. However, the ECM shuts off the throttle actuator current when the ETCS malfunctions.



PROCEDURE

1.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle body with motor assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>THROTTLE BODY>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C67-2 (M+) - C98-14 (M+) Always Below 1 Ω
C67-1 (M-) - C98-15 (M-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C67-2 (M+) or C98-14 (M+) - Body ground Always 10 kΩ or higher
C67-1 (M-) or C98-15 (M-) - Body ground Always 10 kΩ or higher



d.

Reconnect the throttle body with motor assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and housing.

OK:

No foreign objects between throttle valve and housing.



Result:
Proceed to
OK
NG



OK

4.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN OBJECT AND CLEAN THROTTLE BODY

4.CHECK THROTTLE BODY WITH MOTOR ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.



Result:
Proceed to
OK
NG



OK

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY