Home › Engine / Hybrid System › 2TR-FBE ENGINE CONTROL › SFI SYSTEM › 2011.10–2012.10
RM1840EF _51 Engine / Hybrid System _009571 2TR-FBE ENGINE CONTROL _0052126 SFI SYSTEM C

2TR-FBE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


CAUTION / NOTICE / HINT

HINT:
·

These DTCs relate to the accelerator pedal sensor.

·

This electronic throttle control system does not use a throttle cable.



DESCRIPTION

The accelerator pedal sensor is mounted on the accelerator pedal bracket and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type. It uses Hall-effect elements in order to yield accurate signals, even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0 V and 5 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal position (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal sensor itself.

The ECM monitors the actual accelerator pedal position (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A250536
4.344,1.521 4.219,1.438 false 4.344,1.688 4.229,1.635 false 4.344,1.74 4.229,1.833 false 4.344,1.906 4.229,2.021 false 4.354,2.406 4.219,2.406 false 4.375,2.615 4.219,2.615 false 0.844,2.375 0.979,0.594 0.979,0.594 1.063,0.594 false 4.333,1.458 3.896,0.229 false 0.854,1.76 0.656,0.323 0.656,0.323 0.76,0.323 false 1.073,2.052 1.073,0.865 1.073,0.865 1.188,0.865 false 0.844,2.646 0.604,3 0.604,3 0.688,3 false 0.333,3.281 2.052,3.49 1.719,0.208 10 false Accelerator Pedal Sensor 0.792,0.25 1.375,0.469 0.583,0.219 10 false Magnet 1.219,0.792 1.885,1.01 0.667,0.219 10 false No. 1 IC 1.083,0.521 1.719,0.74 0.635,0.219 10 false No. 2 IC 2.073,1.24 2.458,1.469 0.385,0.229 10 false VPA 2.073,1.563 2.427,1.802 0.354,0.24 10 false EPA 2.073,1.885 2.552,2.146 0.479,0.26 10 false VCPA 2.073,2.188 2.531,2.438 0.458,0.25 10 false VPA2 2.073,2.5 2.521,2.719 0.448,0.219 10 false EPA2 2.073,2.823 2.51,3.052 0.438,0.229 10 false VCP2 2.698,3.177 3.135,3.375 0.438,0.198 10 false ECM 4.271,1.042 4.573,1.229 0.302,0.188 10 false *1 5.865,1.042 6.115,1.24 0.25,0.198 10 false *2 3.938,1.333 4.313,1.552 0.375,0.219 10 false 4.55 3.865,1.542 4.313,1.75 0.448,0.208 10 false 3.988 3.938,1.75 4.302,1.948 0.365,0.198 10 false 3.75 3.865,1.958 4.302,2.146 0.438,0.188 10 false 3.188 4,2.313 4.25,2.49 0.25,0.177 10 false 1.6 4,2.531 4.333,2.76 0.333,0.229 10 false 0.8 4.417,2.844 4.854,3.083 0.438,0.24 10 false 0.29 4.26,3.094 4.417,3.271 0.156,0.177 10 false 0 4.688,3.094 5.656,3.375 0.969,0.281 10 false Usable Range 4.375,3.479 6.229,3.708 1.854,0.229 10 false Accelerator Pedal Angle (°) 4.375,3.813 6.76,4.063 2.385,0.25 10 false *1: Accelerator Pedal Fully Released 4.375,4.167 6.885,4.417 2.51,0.25 10 false *2: Accelerator Pedal Fully Depressed 0.719,2.927 1.302,3.167 0.583,0.24 10 false Magnet 1.771,0.125 3.938,0.563 2.167,0.438 10 false Accelerator Pedal Position Sensor Output Voltage (V) 5.792,3.094 6.229,3.333 0.438,0.24 10 false 15.9

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1-trip detection logic).
·

Accelerator pedal rod assembly

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1-trip detection logic).
·

Accelerator pedal rod assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input VPA is 4.8 V or higher for 2.0 seconds or more (1-trip detection logic).
·

Accelerator pedal rod assembly

·

Open in EPA circuit

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1-trip detection logic).
·

Accelerator pedal rod assembly

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is fully released (1-trip detection logic).
·

Accelerator pedal rod assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Conditions (a) and (b) are met for 2.0 seconds or more (1-trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal rod assembly

·

Open in EPA2 circuit

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Condition (a) or (b) is met for 2.0 seconds or more (1-trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal rod assembly

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area Accel Sensor Out No.1
When Accelerator Pedal Released
Accel Sensor Out No.2
When Accelerator Pedal Released
Accel Sensor Out No.1
When Accelerator Pedal Depressed
Accel Sensor Out No.2
When Accelerator Pedal Depressed
VCPA or VCP2 circuit open 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.98 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
EPA or EPA2 circuit open 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V 4.5 to 5.0 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.98 V


HINT:

Accelerator pedal positions are expressed as voltages.


FAIL-SAFE

When DTC P2120, P2122, P2123, P2125, P2127, P2128 or P2138 is stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM uses the remaining circuit to calculate the accelerator pedal position to allow the vehicle to continue to be driven. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles. The ECM continues operating in fail-safe mode until a pass condition is detected and the ignition switch is turned off.

WIRING DIAGRAM

A162855
6.021,3.125 6.469,3.333 0.448,0.208 10 false ECM 5.948,0.885 6.448,1.073 0.5,0.188 10 false VPA 5.948,0.479 6.427,0.729 0.479,0.25 10 false EPA 5.604,1.229 6.146,1.448 0.542,0.219 10 false VCPA 5.948,2.156 6.521,2.396 0.573,0.24 10 false VPA2 5.938,1.719 6.531,1.948 0.594,0.229 10 false EPA2 5.594,2.479 6.167,2.76 0.573,0.281 10 false VCP2 1.573,0.49 2.01,0.719 0.438,0.229 10 false EPA 1.573,0.906 2.031,1.104 0.458,0.198 10 false VPA 1.479,1.323 2,1.552 0.521,0.229 10 false VCPA 1.5,1.74 2,1.948 0.5,0.208 10 false EPA2 1.5,2.167 1.969,2.385 0.469,0.219 10 false VPA2 1.479,2.594 1.969,2.813 0.49,0.219 10 false VCP2 6.01,2.969 6.49,3.26 0.479,0.292 10 false G146 5.396,0.802 5.594,0.969 0.198,0.167 10 false 6 1.99,0.385 2.104,0.552 0.115,0.167 10 false 5 1.99,0.802 2.104,0.969 0.115,0.167 10 false 6 1.99,1.229 2.104,1.396 0.115,0.167 10 false 4 1.99,1.646 2.104,1.813 0.115,0.167 10 false 2 1.99,2.063 2.104,2.229 0.115,0.167 10 false 3 1.99,2.49 2.104,2.656 0.115,0.167 10 false 1 5.396,0.375 5.594,0.542 0.198,0.167 10 false 2 5.396,1.229 5.594,1.396 0.198,0.167 10 false 4 5.396,2.073 5.594,2.24 0.198,0.167 10 false 5 5.396,1.646 5.594,1.813 0.198,0.167 10 false 1 5.396,2.479 5.594,2.646 0.198,0.167 10 false 3 0.365,2.979 0.688,3.229 0.323,0.25 10 false G6 0.365,3.146 2.792,3.396 2.427,0.25 10 false Accelerator Pedal Sensor Assembly

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (ACCEL SENSOR OUT NO.1 AND ACCEL SENSOR OUT NO.2)
a.
A208621
2.438,1.76 3.146,1.99 0.708,0.229 10 false Released 0.531,1.771 1.333,2 0.802,0.229 10 false Depressed

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 234 280,281

e.

Read the value displayed on the tester.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No.1 Accel Sensor Out No.2 Difference between Accel Sensor Out No. 1 and Accel Sensor Out No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V More than 0.02 V
Depressed 2.6 to 4.5 V 3.4 to 4.98 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ROD ASSEMBLY - ECM)
2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL ROD ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal rod assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
G6-6 (VPA) - G146-6 (VPA) Always Below 1 Ω
G6-5 (EPA) - G146-2 (EPA) Always Below 1 Ω
G6-4 (VCPA) - G146-4 (VCPA) Always Below 1 Ω
G6-3 (VPA2) - G146-5 (VPA2) Always Below 1 Ω
G6-2 (EPA2) - G146-1 (EPA2) Always Below 1 Ω
G6-1 (VCP2) - G146-3 (VCP2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
G6-6 (VPA) or G146-6 (VPA) - Body ground Always 10 kΩ or higher
G6-5 (EPA) or G146-2 (EPA) - Body ground Always 10 kΩ or higher
G6-4 (VCPA) or - G146-4 (VCPA) - Body ground Always 10 kΩ or higher
G6-3 (VPA2) or G146-5 (VPA2) - Body ground Always 10 kΩ or higher
G6-2 (EPA2) or G146-1 (EPA2) - Body ground Always 10 kΩ or higher
G6-1 (VCP2) or G146-3 (VCP2) - Body ground Always 10 kΩ or higher



d.

Reconnect the accelerator pedal rod assembly connector.


e.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ACCELERATOR PEDAL ROD ASSEMBLY - ECM)

3.INSPECT ECM (VCPA AND VCP2 VOLTAGE)
a.
A251655
0.198,0.979 0.542,1.219 0.344,0.24 0.667,1.771 1.115,1.24 true 1.198,1.781 1.344,1.25 true 2.469,1.771 2.073,1.25 true 1.75,1.781 1.823,1.25 true 0.188,0.115 0.51,0.396 0.323,0.281 10 false *a 0.281,1.021 0.604,1.302 0.323,0.281 10 false G6 1.583,1.813 2.146,2.063 0.563,0.25 10 false VCPA 1.021,1.813 1.583,2.063 0.563,0.25 10 false EPA2 0.51,1.813 1.073,2.063 0.563,0.25 10 false VCP2 2.365,1.813 2.927,2.063 0.563,0.25 10 false EPA
*a Front view of wire harness connector
(to accelerator pedal rod assembly)


Disconnect the accelerator pedal rod assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G6-4 (VCPA) - G6-5 (EPA) Ignition switch ON 4.5 to 5.5 V
G6-1 (VCP2) - G6-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY

NG

4.REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
a.

Replace the accelerator pedal rod assembly.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>ACCELERATOR PEDAL>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (ACCELERATOR PEDAL SENSOR DTCS)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the Ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Start the engine.


f.

Allow the engine to idle for 15 seconds.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
DTC P2120, P2122, P2123, P2125, P2127, P2128, and/or P2138 is output A
DTC is not output B




A

B

END