The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.
Refer to DTC P0201 (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>P0201).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Disconnect the fuel injector assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C65-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C2-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C66-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C4-1 - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Reconnect the fuel injector assembly connectors.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>2TR-FBE FUEL>FUEL INJECTOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-2 - C98-6 (#10) | Always | Below 1 Ω |
| C2-2 - C98-7 (#20) | Always | Below 1 Ω |
| C66-2 - C98-8 (#30) | Always | Below 1 Ω |
| C4-2 - C98-9 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-2 or C98-6 (#10) - Body ground | Always | 10 kΩ or higher |
| C2-2 or C98-7 (#20) - Body ground | Always | 10 kΩ or higher |
| C66-2 or C98-8 (#30) - Body ground | Always | 10 kΩ or higher |
| C4-2 or C98-9 (#40) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the fuel injector assembly connectors.
Disconnect the ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 - G9-6 (IG2) | Always | Below 1 Ω |
| C2-1 - G9-6 (IG2) | Always | Below 1 Ω |
| C66-1 - G9-6 (IG2) | Always | Below 1 Ω |
| C4-1 - G9-6 (IG2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C65-1 or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| C2-1 or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| C66-1 or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
| C4-1 or G9-6 (IG2) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector connector.
Reconnect the ignition switch connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG