Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009572 1GR-FE ENGINE CONTROL _0052127 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  P0345  Camshaft Position Sensor "A" Circuit (Bank 2)  P0347  Camshaft Position Sensor "A" Circuit Low Input (Bank 2)  P0348  Camshaft Position Sensor "A" Circuit High Input (Bank 2)  


DESCRIPTION

The Variable Valve Timing (VVT) sensor (VV1, 2 signal) of the intake camshaft consists of a magnet and MRE (Magnetic Resistance Element).

The VVT camshaft drive gear has a sensor plate with 3 teeth on its outer circumference. When the gear rotates, changes occur in the air gaps between the sensor plate and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the gear rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

The crankshaft angle sensor plate has 34 teeth. The pickup coil generates 34 signals for each revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction When either condition below is met:
·

No VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).

·

No VVT sensor signal is sent to the ECM during cranking for 4 seconds or more (2 trip detection logic).


·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor is below 0.3 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage of the VVT sensor is higher than 4.7 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0345 Camshaft Position Sensor "A" Circuit (Bank 2) When either condition below is met:
·

No VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).

·

No VVT sensor signal is sent to the ECM during cranking for 4 seconds or more (2 trip detection logic).


·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) The output voltage of the VVT sensor is below 0.3 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored
P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) The output voltage of the VVT sensor is higher than 4.7 V for 5 seconds (1 trip detection logic).
·

Open or short in VVT sensor circuit

·

VVT sensor

·

Camshaft timing gear assembly

·

Jumped tooth of timing chain

·

ECM


Comes on DTC stored

A107148
1.313,2.906 2.344,3.104 1.031,0.198 10 false 20 msec./DIV. 0.156,0.917 0.844,1.115 0.688,0.198 10 false 5 V/DIV. 0.177,1.563 0.458,1.76 0.281,0.198 10 false NE 0.094,2.052 0.458,2.25 0.365,0.198 10 false VV1 3.042,1.563 3.375,1.76 0.333,0.198 10 false GND 3.063,2.167 3.396,2.365 0.333,0.198 10 false GND 3.063,2.563 3.396,2.76 0.333,0.198 10 false GND 0.104,2.458 0.469,2.656 0.365,0.198 10 false VV2 0.333,0.292 2.74,0.49 2.406,0.198 10 false VV1, VV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveform is as shown.

·

VV1+ and VV2+ stand for the VVT sensor signal, and NE+ stands for the crankshaft position sensor signal.



Item Content
Terminal NE+ - NE-
VV1+ - VV1-
VV2+ - VV2-
Equipment Setting 5 V/DIV.
20 msec./DIV.
Condition Cranking or idling


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on.

6.

Start the engine.

7.

Idle the engine for 10 seconds or more.

8.

Enter the following menus: Powertrain / Engine and ECT / DTC.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0340, P0342, P0343, P0345, P0347 or P0348.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

A279107
1.271,2.406 1.688,2.594 0.417,0.188 10 false C138 1.271,2.573 2.844,2.771 1.573,0.198 10 false VVT Sensor (for Bank 1) 1.271,4.813 1.771,5 0.5,0.188 10 false C146 1.281,4.979 2.854,5.177 1.573,0.198 10 false VVT Sensor (for Bank 2) 5.177,0.823 5.458,0.969 0.281,0.146 10 false VC 5.177,1.354 5.583,1.51 0.406,0.156 10 false VV1+ 5.177,1.906 5.542,2.063 0.365,0.156 10 false VV1- 5.167,3.792 5.573,3.948 0.406,0.156 10 false VV2+ 5.167,4.344 5.531,4.5 0.365,0.156 10 false VV2- 4.75,0.948 5.146,1.125 0.396,0.177 10 false C129 4.76,1.49 5.156,1.667 0.396,0.177 10 false C131 4.75,2.031 5.146,2.208 0.396,0.177 10 false C131 4.75,3.906 5.135,4.083 0.385,0.177 10 false C131 4.75,4.448 5.125,4.625 0.375,0.177 10 false C131 5.823,5.188 6.167,5.375 0.344,0.188 10 false ECM 4.833,0.781 5.042,0.969 0.208,0.188 10 false 23 4.844,1.313 5.031,1.51 0.188,0.198 10 false 19 4.833,1.844 5.021,2.01 0.188,0.167 10 false 29 4.823,3.708 5.021,3.875 0.198,0.167 10 false 18 4.833,4.26 5.021,4.427 0.188,0.167 10 false 28 2.646,0.833 2.771,1 0.125,0.167 10 false 3 2.646,1.385 2.75,1.563 0.104,0.177 10 false 1 2.646,1.927 2.75,2.073 0.104,0.146 10 false 2 2.646,3.281 2.771,3.448 0.125,0.167 10 false 3 2.635,3.781 2.74,3.958 0.104,0.177 10 false 1 2.635,4.344 2.74,4.49 0.104,0.146 10 false 2 2.302,0.854 2.521,1.031 0.219,0.177 10 false VC 2.177,1.385 2.594,1.552 0.417,0.167 10 false VVR+ 2.188,1.917 2.563,2.083 0.375,0.167 10 false VVR- 2.302,3.271 2.521,3.448 0.219,0.177 10 false VC 2.177,3.802 2.594,3.969 0.417,0.167 10 false VVL+ 2.188,4.333 2.604,4.5 0.417,0.167 10 false VVL- 1.604,1.385 1.74,1.552 0.135,0.167 10 false * 1.604,3.792 1.74,3.958 0.135,0.167 10 false * 0.073,5.354 4.406,5.542 4.333,0.188 10 false *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include No. 1 cylinder.



PROCEDURE

1.CHECK VVT SENSOR (SENSOR POWER SOURCE)
a.
A208648
0.417,0.948 0.854,1.229 0.438,0.281 0.417,1.302 0.854,1.583 0.438,0.281 1.979,1.375 2.271,1.677 true 0.479,1 0.885,1.24 0.406,0.24 10 false C138 0.479,1.354 0.885,1.594 0.406,0.24 10 false C146 2.313,1.688 2.594,1.854 0.281,0.167 10 false VC 0.083,0.042 0.271,0.208 0.188,0.167 10 false *a 0.885,1.01 1.146,1.188 0.26,0.177 10 false *A 0.896,1.344 1.219,1.563 0.323,0.219 10 false *B
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to VVT Sensor)


Disconnect the VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C138-3 (VC) - Body ground Always 4.5 to 5.5 V
C146-3 (VC) - Body ground Always 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C138-1 (VVR+) - C131-19 (VV1+) Always Below 1 Ω
C138-2 (VVR-) - C131-29 (VV1-) Always Below 1 Ω
C146-1 (VVL+) - C131-18 (VV2+) Always Below 1 Ω
C146-2 (VVL-) - C131-28 (VV2-) Always Below 1 Ω
C138-1 (VVR+) or C131-19 (VV1+) - Body ground Always 10 kΩ or higher
C138-2 (VVR-) or C131-29 (VV1-) - Body ground Always 10 kΩ or higher
C146-1 (VVL+) or C131-18 (VV2+) - Body ground Always 10 kΩ or higher
C146-2 (VVL-) or C131-28 (VV2-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION
a.
A295942
0.417,1.885 0.729,2.083 0.313,0.198 10 OK 2.667,1.885 2.979,2.083 0.313,0.198 10 NG 1.688,1.573 2.396,1.771 0.708,0.198 10 Clearance

Check the VVT sensor installation.

OK:

Sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.CHECK VALVE TIMING

NG

4.CHECK VALVE TIMING
a.
A301881
0.802,0.844 2.354,0.5 2.354,0.5 2.344,0.854 true 0.771,1.177 2.365,2.26 2.365,2.26 2.438,1.281 true 0.875,3.615 1.781,4.292 1.781,4.292 2.417,3.5 true 1.771,4.281 1.031,3.615 true 0.104,0.094 0.417,0.292 0.313,0.198 10 false *A 0.135,2.313 0.448,2.51 0.313,0.198 10 false *B 2.375,2.292 2.688,2.49 0.313,0.198 10 false *a 1.729,4.281 2.042,4.479 0.313,0.198 10 false *a 2.333,0.344 2.646,0.542 0.313,0.198 10 false *a
*A for Bank 1
*B for Bank 2
*a Timing Mark


Remove the cylinder head cover sub-assembly RH and LH.

Click hereEngine / Hybrid System>1GR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL


b.

Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration. If not, turn the crankshaft 1 revolution (360°), and then align the marks as described above.

OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.



Result:
Proceed to
OK
NG



OK

5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)

NG

5.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE)
a.

Check the teeth of the signal plate.

OK:

Sensor plate teeth do not have any cracks or deformation.



Result:
Proceed to
OK
NG



OK

6.REPLACE VVT SENSOR

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

6.REPLACE VVT SENSOR

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS
7.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON and turn the tester on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Start the engine.


f.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.

Powertrain > Engine > Trouble Codes
50001 61

h.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
P0340, P0342, P0343, P0345, P0347 or P0348 is output B


HINT:

If the engine does not start, replace the ECM.




A

END

B

8.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C138-3 (VC) - C129-23 (VC) Always Below 1 Ω
C146-3 (VC) - C129-23 (VC) Always Below 1 Ω
C138-3 (VC) or C129-23 (VC) - Body ground Always 10 kΩ or higher
C146-3 (VC) or C129-23 (VC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR