Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › ENGINE UNIT(w/o DPF)
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052172 ENGINE UNIT(w/o DPF) A

2KD-FTV ENGINE MECHANICAL  ENGINE UNIT(w/o DPF)  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 2.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 8.REMOVE VALVE LIFTER

a.

Remove the valve lifters.

HINT:

Arrange the valve lifters in the correct order.



Hide 10.REMOVE CYLINDER HEAD GASKET

Hide 11.REMOVE WATER PUMP ASSEMBLY

a.
A225339

Remove the 5 bolts, 2 nuts, water pump and gasket.


Hide 12.REMOVE TIMING GEAR COVER

NOTICE:

As the fuel supply pump is not installed, the injection gear is loose inside the timing gear case. Do not allow the injection gear to fall.


HINT:

To prevent the injection gear from falling, temporarily install the fuel supply pump.


a.
A100853

Remove the 14 bolts and 2 nuts.


b.
A102800

Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.

NOTICE:

Be careful not to drop the injection gear.



c.
A222328

Remove the O-ring from the timing gear case.


Hide 13.REMOVE INJECTION GEAR

a.
A222329

Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.



b.
A222330

Remove the injection gear.


Hide 14.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A239296

Remove the No. 1 crankshaft position sensor plate.


Hide 15.INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO OIL PUMP GEAR

a.
A060171

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the crankshaft timing gear or timing gear case assembly.


Hide 16.INSPECT BACKLASH OF CRANKSHAFT TIMING GEAR TO NO. 1 IDLE GEAR

a.
A060170

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the crankshaft timing gear or No. 1 idle gear.


Hide 17.INSPECT NO. 1 IDLE GEAR THRUST CLEARANCE

a.

Install the timing gear case, No. 1 idle gear and camshaft timing gear.


b.
A060169

Using a dial indicator, measure the thrust clearance.

Standard thrust clearance:

0.06 to 0.11 mm (0.00236 to 0.00433 in.)


Maximum thrust clearance:

0.3 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the idle gear thrust plate. If necessary, replace the No. 1 idle gear or No. 1 idle gear shaft.


Hide 18.REMOVE CRANKSHAFT TIMING GEAR

a.
A222332
1.448,1.188 0.958,1.635 0.958,1.635 0.875,1.635 false 0.521,1.542 0.833,1.708 0.313,0.167 10 false SST

Using SST, remove the crankshaft timing gear.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05010, 09954-05021)


Hide 19.INSPECT BACKLASH OF INJECTION GEAR TO NO. 1 IDLE GEAR

a.

Install the fuel supply pump with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.
A060158
1.073,1.198 0.729,1.813 0.729,1.813 0.51,1.813 true 0.125,1.74 0.458,1.927 0.333,0.188 10 false SST

Using SST, install the injection gear with the nut.

SST
09960-10010  (09962-01000, 09963-01000)

Torque:
64 N*m (650 kgf*cm, 47 ft.*lbf)


c.
A060172

Using a dial indicator, measure the backlash.

Standard gear backlash:

0.02 to 0.15 mm (0.000787 to 0.00591 in.)


Maximum gear backlash:

0.2 mm (0.00787 in.)


If the gear backlash is more than the maximum, replace the injection gear or No. 1 idle gear.


d.
A060158
1.073,1.198 0.74,1.813 0.74,1.813 0.51,1.813 true 0.125,1.74 0.458,1.927 0.333,0.188 10 false SST

Using SST, remove the nut and injection gear.

SST
09960-10010  (09962-01000, 09963-01000)


e.

Remove the 2 nuts and fuel supply pump.


Hide 20.REMOVE IDLE GEAR THRUST PLATE

a.
A238857

Remove the 2 bolts and idle gear thrust plate.


Hide 21.REMOVE NO. 1 IDLE GEAR

a.
A238858

Remove the No. 1 idle gear together with the No. 2 idle sub gear.


Hide 22.REMOVE NO. 2 IDLE SUB GEAR

a.
A060164
2.292,0.469 2.51,0.198 2.51,0.198 2.573,0.198 false 0.958,1.906 0.594,1.698 0.594,1.698 0.49,1.698 false 2.094,1.76 1.563,1.958 1.563,1.958 1.479,1.958 true 2.021,1.604 2.677,1.438 2.677,1.438 2.781,1.438 true 2.604,0.104 2.938,0.25 0.333,0.146 10 false SST 1.281,1.865 1.458,2.021 0.177,0.156 10 false *2 2.813,1.365 2.969,1.521 0.156,0.156 10 false *3 0.302,1.594 0.469,1.75 0.167,0.156 10 false *1
*1 Service Bolt
*2 No. 1 Idle Gear
*3 No. 2 Idle Sub Gear
V100135

Turn


Using SST, turn the No. 2 idle sub gear clockwise and remove the service bolt.

SST
09960-10010  (09962-01000, 09963-00700)


b.
A060168

Using snap ring pliers, remove the snap ring.


c.

Remove the wave washer, No. 2 idle sub gear and gear spring.


Hide 23.REMOVE NO. 1 IDLE GEAR SHAFT

a.
A238859

Remove the No. 1 idle gear shaft.


Hide 24.REMOVE OIL PAN SUB-ASSEMBLY

a.

Remove the 22 bolts and 2 nuts.


b.
A303108

Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

NOTICE:
·

Do not use the oil pan seal cutter for the area between the oil pan and timing belt case, or for the area between the oil pan and rear oil seal retainer.

·

Be careful not to damage the oil pan flange.




Hide 25.REMOVE OIL STRAINER SUB-ASSEMBLY

a.

Remove the 2 bolts, 2 nuts, oil strainer and gasket.


Hide 26.REMOVE TIMING GEAR CASE ASSEMBLY

a.

Remove the bolt and No. 1 vacuum transmitting pipe.


b.
A060153

Remove the union bolt and 8 bolts.


c.

Pry the timing gear case at the location shown in the illustration and remove the gear case and gasket.


d.
A060152

Remove the 2 O-rings.


Hide 27.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A052295

Remove the 5 bolts.


b.

Using a screwdriver, remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block.


Hide 28.REMOVE FRONT CRANKSHAFT OIL SEAL

a.
A058121

Using a screwdriver and hammer, tap out the oil seal.


Hide 29.REMOVE SUPPLY PUMP OIL SEAL

a.
A058117

Using a screwdriver and hammer, tap out the oil seal.


Hide 30.REMOVE REAR CRANKSHAFT OIL SEAL

a.
A061819

Using a screwdriver and hammer, tap out the oil seal.