Home › Engine / Hybrid System › 2KD-FTV ENGINE MECHANICAL › CAMSHAFT(w/ DPF) › from 2012.04
RM1840EF _51 Engine / Hybrid System _009574 2KD-FTV ENGINE MECHANICAL _0052177 CAMSHAFT(w/ DPF) A

2KD-FTV ENGINE MECHANICAL  CAMSHAFT(w/ DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 4.REMOVE RADIATOR HOSE INLET

Hide 10.REMOVE FRONT WHEEL LH

Hide 15.REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

Hide 16.REMOVE NO. 3 CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 18.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

Hide 27.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

Hide 28.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

Hide 32.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 33.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 34.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 41.REMOVE CAMSHAFT

a.
A060148
0.438,0.698 0.302,1.135 0.302,1.135 0.302,1.25 true 0.208,1.292 0.396,1.469 0.188,0.177 10 false *1
*1 Key Groove


Turn the camshaft with a wrench so that the key groove of the camshaft faces upward.


b.
A060147
1.146,1.354 1.271,1.531 0.125,0.177 10 true 1 0.677,0.958 0.802,1.135 0.125,0.177 10 false 2 0.938,1.125 1.063,1.302 0.125,0.177 10 true 3 2.99,0.229 3.115,0.406 0.125,0.177 10 false 4 2.563,0.021 2.688,0.198 0.125,0.177 10 false 5 2.771,0.094 2.896,0.271 0.125,0.177 10 false 6 1.771,1.042 1.896,1.219 0.125,0.177 10 true 7 1.24,0.646 1.365,0.823 0.125,0.177 10 false 8 1.448,0.813 1.573,0.99 0.125,0.177 10 true 9 2.083,0.156 2.271,0.333 0.188,0.177 10 false 11 2.458,0.469 2.646,0.646 0.188,0.177 10 true 10 2.208,0.323 2.396,0.5 0.188,0.177 10 true 12 2.052,0.74 2.24,0.917 0.188,0.177 10 true 13 1.667,0.375 1.854,0.552 0.188,0.177 10 false 14 1.833,0.563 2.021,0.74 0.188,0.177 10 true 15

Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.


c.

Remove the 15 bearing cap bolts, 5 bearing caps, oil seal and 2 camshafts.