Home › Engine / Hybrid System › 2TR-FBE ENGINE MECHANICAL › ENGINE
RM1840EF _51 Engine / Hybrid System _009576 2TR-FBE ENGINE MECHANICAL _0052193 ENGINE G

2TR-FBE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT AIR CLEANER FILTER ELEMENT

a.

Remove the air cleaner filter element.


b.

Visually check that the air filter is not excessively damaged or oily.

If necessary, replace the air cleaner filter element.


Hide 3.INSPECT NO. 1 IDLER PULLEY

a.

Idle the engine, and then stop the engine. Check that the fan and generator V belt is between the edges of the idler pulley.


b.

Remove the fan and generator V belt.


c.
G035186
2.177,0.396 2.354,0.563 0.177,0.167 10 false *a
*a Turn


Turn the pulley, and check that the idler bearing moves smoothly and quietly.

If necessary, replace the No. 1 idler pulley.


d.

Install the fan and generator V belt.


Hide 4.CHECK VALVE LASH ADJUSTER NOISE

a.

Rev the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for more than 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a lash adjuster inspection (See page Engine / Hybrid System>2TR-FBE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION).


Hide 5.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.

NOTICE:

Switch off all the accessories and the A/C before connecting the intelligent tester.



ii.

Start the engine and idle it.


iii.

Turn the intelligent tester main switch on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

0 to 20° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in neutral or park.


HINT:

Refer to the intelligent tester operator's manual for further details.



v.

Check that the ignition timing advances immediately when the engine speed is increased.


vi.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

vii.

Monitor IGN Advance.


viii.

Perform the Active Test.

Standard ignition timing:

3 to 7° BTDC @ idle


NOTICE:

When checking the ignition timing, the transmission should be in neutral or park.


HINT:

Refer to the intelligent tester operator's manual for further details.




c.

When not using the intelligent tester:

i.
A206183
0.75,1.906 0.875,1.906 0.875,1.906 1.052,1.49 true 0.448,1.823 0.802,2.042 0.354,0.219 10 false TAC 0.052,0.052 0.229,0.229 0.177,0.177 10 false *a
*a Front view of DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:
·

Confirm the terminal number before connecting the probe. Connecting the wrong terminals can damage the engine.

·

Turn off all electrical systems before connecting the probe.




ii.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.


iii.

Start the engine and idle it.


iv.
A206183
1.219,0.375 1.354,0.375 1.354,0.375 1.573,0.885 true 2.115,1.896 1.979,1.896 1.979,1.896 1.813,1.479 true 0.083,0.063 0.281,0.26 0.198,0.198 10 false *a 0.979,0.292 1.26,0.49 0.281,0.198 10 false CG 2.156,1.813 2.417,1.99 0.26,0.177 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

When checking the ignition timing, the transmission should be in neutral.


HINT:
A099876
2.167,0.24 2.49,0.469 0.323,0.229 10 false *b 2.813,0.958 3.094,1.198 0.281,0.24 10 false *c 2.135,1.729 2.385,1.906 0.25,0.177 10 false *e 1.594,1.333 1.823,1.563 0.229,0.229 10 false *d 0.135,0.813 0.385,1.021 0.25,0.208 10 false *a
*a Engine Speed
*b Approx. 1000 to 1500 rpm
*c Idle Speed
*d 5 sec.
*e Connect Terminals TC and CG


·

After connecting terminals TC and CG, the engine speed changes to between approximately 1000 and 1500 rpm for 5 seconds, and then returns to idle as the ECM checks that the ISC (Idle Speed Control) system operates properly.

·

Inspect the ignition timing after the engine speed returns to idle.




v.

Using the timing light, measure the ignition timing.

Standard ignition timing:

3 to 7° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the ignition timing, the transmission should be in neutral or park.




vi.

Remove SST from the DLC3.


vii.

Check the ignition timing.

Standard ignition timing:

0 to 20° BTDC @ idle



viii.

Confirm that the ignition timing advances immediately when the engine speed is increased.


ix.

Turn the ignition switch off.


x.

Disconnect the timing light from the engine.



Hide 6.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3.

NOTICE:

Switch off all accessories and the air conditioning before connecting the intelligent tester.



ii.

Start the engine and idle it.


iii.

Turn the intelligent tester on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9
Standard idle speed:

600 to 700 rpm


NOTICE:

When checking the idle speed, the transmission should be in neutral.


HINT:

Refer to the intelligent tester operator's manual for further details.



v.

Turn the ignition switch off.


vi.

Disconnect the intelligent tester from the DLC3.



c.

When not using the intelligent tester:

i.
A206183
0.75,1.906 0.875,1.906 0.875,1.906 1.052,1.49 true 0.448,1.823 0.802,2.042 0.354,0.219 10 false TAC 0.052,0.052 0.229,0.229 0.177,0.177 10 false *a
*a Front view of DLC3


Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  


ii.

Start the engine and idle it.


iii.

Check the idle speed.

Standard idle speed:

600 to 700 rpm




Hide 7.INSPECT IDLE SPEED CONTROL SYSTEM

a.

Warm up and stop the engine.


b.

Check the idle speed control system.

i.
A206183
1.219,0.375 1.354,0.375 1.354,0.375 1.573,0.885 true 2.115,1.896 1.979,1.896 1.979,1.896 1.813,1.479 true 0.083,0.063 0.281,0.26 0.198,0.198 10 false *a 0.979,0.292 1.26,0.49 0.281,0.198 10 false CG 2.156,1.813 2.417,1.99 0.26,0.177 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Start the engine and idle it.

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

·

Turn off all electrical systems before connecting the terminals.

·

When checking the idle speed, the transmission should be in neutral.




iii.
A099876
2.167,0.24 2.49,0.469 0.323,0.229 10 false *b 2.813,0.958 3.094,1.198 0.281,0.24 10 false *c 2.135,1.729 2.385,1.906 0.25,0.177 10 false *e 1.594,1.333 1.823,1.563 0.229,0.229 10 false *d 0.135,0.813 0.385,1.021 0.25,0.208 10 false *a
*a Engine Speed
*b Approx. 1000 to 1500 rpm
*c Idle Speed
*d 5 sec.
*e Connect Terminals TC and CG


After connecting terminals TC and CG, check that the engine speed changes to between approximately 1000 and 1500 rpm for 5 seconds, and then returns to idle.

If the result is not as specified, check the throttle body and wire harness, and check for DTCs (See page Engine / Hybrid System>2TR-FBE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR) and wire harness.



Hide 8.INSPECT COMPRESSION

a.

Warm up and stop the engine.



c.

Disconnect the 4 fuel injector connectors.



e.

Check the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1230 kPa (12.5 kgf/cm2, 178 psi) or higher


Minimum pressure:

880 kPa (9.0 kgf/cm2, 128 psi)


Difference between each cylinder:

68 kPa (0.7 kgf/cm2, 9.9 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as short a time as possible.



If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and perform the inspection again.

HINT:
·

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.





f.

Connect the 4 fuel injector connectors.




Hide 9.CHECK CO/HC

a.

Start and warm up the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds, and then idle the engine.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe.


d.

Check the CO/HC concentration at idle.

Standard idle CO concentration:

0 to 0.5%


Standard idle HC concentration:

Refer to applicable local regulation



e.

If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.


ii.

See the table below for possible causes, and then inspect and repair the applicable causes if necessary.

CO HC Problems Causes
Normal High Rough idle
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leaks in intake and exhaust valves

4.

Leaks in cylinders


Low High Rough idle
(Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)
1.

Restricted air cleaner filter element

2.

Plugged PCV valve

3.

Faulty SFI system:

·

Faulty pressure regulator

·

Defective engine coolant temperature sensor

·

Defective mass air flow meter

·

Faulty ECM

·

Faulty injectors

·

Faulty throttle position sensor