Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CYLINDER HEAD GASKET › from 2012.04
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052207 CYLINDER HEAD GASKET A

1GR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 2 CYLINDER HEAD GASKET

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head LH or cylinder block.


b.
A301924
1.99,1.052 2.135,0.906 2.135,0.906 2.26,0.906 false 2.229,1.333 2.406,1.51 2.406,1.51 2.552,1.51 false 2,1.635 2.177,1.792 2.177,1.792 2.323,1.792 false 0.219,0.469 0.375,0.667 0.156,0.198 10 false A 0.208,2.344 0.365,2.542 0.156,0.198 10 false A 1.74,1.813 1.896,2.01 0.156,0.198 10 false B 2.313,0.802 2.469,1 0.156,0.198 10 false *1 2.396,1.677 2.552,1.875 0.156,0.198 10 false *1 2.615,1.385 2.771,1.583 0.156,0.198 10 false *2
*1 Seal Packing
*2 Gasket


Apply seal packing to a new No. 2 cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.0 mm (0.0984 to 0.118 in.)


Seal Packing Application Range
A 10 to 15 mm (0.394 to 0.591 in.)
B 1.25 to 1.5 mm (0.0492 to 0.0591 in.)

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 cylinder head gasket within 3 minutes after applying the seal packing.

·

Do not add engine oil within 2 hours of installation.




c.
A301945
1.885,1.667 1.979,1.917 1.979,1.917 2.167,1.917 false 2.219,1.813 2.531,2.01 0.313,0.198 10 false *1
*1 Lot No.
V100135

Engine Front


Place the No. 2 cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

NOTICE:

Make sure that the gasket is installed facing the proper direction.



d.
A251936
1.438,0.979 0.75,0.979 true 2.552,0.323 2.708,0.323 2.708,0.323 2.969,1.281 true 0.052,0 0.271,0.208 0.219,0.208 10 false *a 2.344,0.25 2.521,0.427 0.177,0.177 10 false *1 2.479,0.885 2.667,1.063 0.188,0.177 10 false *2 2.385,1.448 2.573,1.635 0.188,0.188 10 false *3 0.563,0.885 0.74,1.063 0.177,0.177 10 false *b
*1 No. 2 Cylinder Head Gasket
*2 Cylinder Head LH
*3 Cylinder Block
*a Engine Front Side
*b Wipe Clean


Seal packing will seep out from the front side of engine. Thoroughly wipe off the seal packing that seeps out.


Hide 2.INSTALL CYLINDER HEAD LH

a.

Place the cylinder head LH on the cylinder block.

NOTICE:
·

Gently place the cylinder head LH in order not to damage the gasket with the bottom part of the head.

·

Make sure that no oil is on the mounting surface of the cylinder head LH.



HINT:

The cylinder head bolts are tightened in 2 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



b.
A301944
0.938,0.333 1.094,0.531 0.156,0.198 10 false 8 1.563,0.344 1.719,0.542 0.156,0.198 10 false 1 2.219,0.354 2.375,0.552 0.156,0.198 10 false 3 2.802,0.375 2.958,0.573 0.156,0.198 10 false 5 2.792,1.833 2.948,2.031 0.156,0.198 10 false 7 2.24,1.833 2.396,2.031 0.156,0.198 10 false 2 1.563,1.833 1.719,2.031 0.156,0.198 10 false 4 0.917,1.823 1.073,2.021 0.156,0.198 10 false 6

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not drop the washers into the cylinder head LH.




c.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts another 180°.


iii.

Check that the paint marks are now at a 180° angle to the front.



d.
A072969
0.177,0.479 0.302,0.625 0.125,0.146 10 false 2 0.177,1.26 0.302,1.406 0.125,0.146 10 false 1

Install the 2 bolts in the order shown in the illustration.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 3.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY AND NO. 4 CAMSHAFT SUB-ASSEMBLY

Hide 4.INSTALL CYLINDER HEAD GASKET

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head or cylinder block.


b.
A301947
2.156,1.354 2.333,1.208 2.333,1.208 2.479,1.208 false 2.208,1.896 2.396,2.188 2.396,2.188 2.583,2.188 false 2.469,1.635 2.594,1.833 2.594,1.833 2.74,1.833 false 0.229,0.615 0.51,0.823 0.281,0.208 10 false A 0.208,2.76 0.49,2.969 0.281,0.208 10 false A 1.906,2.125 2.188,2.333 0.281,0.208 10 false B 2.521,1.115 2.833,1.313 0.313,0.198 10 false *1 2.625,2.094 2.938,2.292 0.313,0.198 10 false *1 2.792,1.74 3.104,1.938 0.313,0.198 10 false *2
*1 Seal Packing
*2 Gasket


Apply seal packing to a new cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.5 to 3.0 mm (0.0984 to 0.118 in.)


Seal Packing Application Range
A 10 to 15 mm (0.394 to 0.591 in.)
B 1.25 to 1.5 mm (0.0492 to 0.0591 in.)

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head gasket within 3 minutes after applying the seal packing.

·

Do not add engine oil within 2 hours of installation.




c.
A301946
1.667,0.469 1.833,0.229 1.833,0.229 1.99,0.229 false 2.042,0.135 2.354,0.333 0.313,0.198 10 false *1
*1 Lot No.
V100135

Engine Front


Place the cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

NOTICE:

Make sure that the gasket is installed facing the proper direction.



Hide 5.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Place the cylinder head RH on the cylinder block.

NOTICE:
·

Gently place the cylinder head in order not to damage the gasket with the bottom part of the head.

·

Make sure that no oil is on the mounting surface of the cylinder head.



HINT:

The cylinder head bolts are tightened in 2 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



b.
A301943
0.719,0.146 0.875,0.344 0.156,0.198 10 false 6 1.375,0.167 1.531,0.365 0.156,0.198 10 false 4 2.031,0.177 2.188,0.375 0.156,0.198 10 false 2 2.646,0.167 2.802,0.365 0.156,0.198 10 false 7 2.656,1.646 2.813,1.844 0.156,0.198 10 false 5 2.01,1.646 2.167,1.844 0.156,0.198 10 false 3 1.365,1.646 1.521,1.844 0.156,0.198 10 false 1 0.74,1.646 0.896,1.844 0.156,0.198 10 false 8

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:

Do not drop the washers into the cylinder head.




c.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts another 180°.


iii.

Check that the paint marks are now at a 180° angle to the front.



d.
A251936
1.438,0.979 0.75,0.979 true 2.552,0.323 2.708,0.323 2.708,0.323 2.969,1.281 true 0.052,0 0.271,0.208 0.219,0.208 10 false *a 2.344,0.25 2.521,0.427 0.177,0.177 10 false *1 2.479,0.885 2.667,1.063 0.188,0.177 10 false *2 2.385,1.448 2.573,1.635 0.188,0.188 10 false *3 0.563,0.885 0.74,1.063 0.177,0.177 10 false *b
*1 No. 2 Cylinder Head Gasket
*2 Cylinder Head LH
*3 Cylinder Block
*a Engine Front Side
*b Wipe Clean


Seal packing will seep out from the front side of engine. Thoroughly wipe off the seal packing that seeps out.


Hide 10.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

Hide 12.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

Hide 14.INSTALL CHAIN TENSIONER SLIPPER

Hide 21.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY