Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL PUMP › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009602 1GR-FE LUBRICATION _0052411 OIL PUMP A

1GR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.


b.

Install a new O-ring to the cylinder head for bank 2.


c.
A302593
0.656,1.563 1.448,1.563 1.448,1.563 1.448,1.021 true 2.313,1.563 1.74,1.563 1.74,1.563 1.74,1.021 true 0.656,1.979 0.656,1.479 true 2.313,1.948 2.313,1.375 true 0.583,2 0.896,2.198 0.313,0.198 10 true *1 2.26,1.979 2.573,2.177 0.313,0.198 10 true *1
*1 Seal Packing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.5 mm (0.138 to 0.177 in.)



d.

Apply seal packing in a continuous line to the timing chain cover as shown in the illustration.

A302594
5.76,1.365 5.698,1.281 5.698,1.281 5.521,1.281 false 6.396,1.375 6.479,1.281 6.479,1.281 6.688,1.281 false 3.854,1.031 3.948,0.354 3.948,0.354 2.552,0.521 true 2.26,2.115 1.063,2.375 1.063,2.375 2.354,1.719 true 1.51,2.615 1.073,2.375 1.073,2.375 1.854,2.104 true 0.875,2.302 1.188,2.458 0.313,0.156 10 false *1 3.021,3.323 3.333,3.479 0.313,0.156 10 false *a 5.031,2.917 5.344,3.073 0.313,0.156 10 false *b 5.031,3.094 5.344,3.25 0.313,0.156 10 false *c 5.896,0.844 6.354,1.01 0.458,0.167 10 false B - B 6.365,1.813 6.677,1.969 0.313,0.156 10 false *a 5.344,1.198 5.656,1.354 0.313,0.156 10 false *1 6.74,1.188 7.052,1.344 0.313,0.156 10 false *1 5.521,2.198 6.865,2.427 1.344,0.229 10 false 16.7 mm (0.657 in.) 3.948,0.188 4.26,0.344 0.313,0.156 10 false *1 0.99,0.865 1.146,1.063 0.156,0.198 10 false A 1.354,1.344 1.51,1.542 0.156,0.198 10 false B 1.01,1.49 1.167,1.688 0.156,0.198 10 false B
*1 Seal Packing - -
*a Application Position from Inside Seal Line *b Continuous line area
*c Dashed line area - -


Seal Packing:
Item Seal Packing
Continuous Line Area Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Dashed Line Area Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Application Specification:
Seal Packing Diameter Application Position from Inside Seal Line
3.5 to 4.5 mm (0.138 to 0.177 in.) 3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Install the timing chain cover within 3 minutes after applying seal packing. After installing it, the timing chain cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

·

Do not apply seal packing to "A" shown in the illustration.




e.
A302595
0.521,0.344 0.813,0.531 0.292,0.188 10 false 15°

Align the keyway of the oil pump drive rotor with the rectangular portion of the crankshaft timing gear and slide the timing chain cover into place.


f.
A251902
0.323,1.177 0.396,1.156 false
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Install the timing chain cover with the 24 bolts labeled A and B, and the 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

Standard Bolt:
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 55 mm (2.17 in.)


NOTICE:
·

Make sure not to wrap the chain and slipper over the timing chain cover seal line.

·

Make sure that there is no oil on the bolt threads.




Hide 3.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

a.

Install a new gasket and the oil filter bracket with the 3 bolts and 2 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.


b.
A076311
0.677,0.479 0.25,0.313 0.25,0.313 0.677,1.781 true 0.031,0.229 0.208,0.406 0.177,0.177 10 false *1
*1 Seal Packing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:

Install the cylinder head cover within 3 minutes after applying seal packing. After installing it, cylinder head cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.



c.

Install a new gasket to the cylinder head cover.


d.

Install a new seal washers to the bolts.


e.
A251907
0.365,1.479 0.354,1.531 false
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover and cylinder head cover.


b.
A076310
2.719,0.531 3.115,0.375 3.115,0.375 2.719,1.854 true 3.146,0.24 3.333,0.396 0.188,0.156 10 false *1
*1 Seal Packing


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:

Install the cylinder head cover within 3 minutes after applying seal packing. After installing it, cylinder head cover bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.



c.

Install a new gasket to the cylinder head cover.


d.

Install a new seal washers to the bolts.


e.
A251908
1.25,1.875 1.26,1.927 false
V100135

Bolt A
V100136

Bolt B
V100137

Nut


Temporarily install the cylinder head cover with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 7.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.


b.

Install a new O-ring to the timing chain cover.


c.
A191345
2.1,0.157 2.275,0.322 0.175,0.165 10 *1 2.069,0.25 1.884,0.25 1.884,0.25 1.572,0.65 false
*1 Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes after applying seal packing. After installing the oil pan, the oil pan bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

·

Do not start the engine for at least 2 hours after installing.




d.
A251903
2.073,1.667 2.021,1.167 true 2.594,1.281 2.01,1.167 2.01,1.167 2.594,1.604 true 2.594,0.656 2.01,1.177 2.01,1.177 2.594,0.979 true 1.802,1.094 1.969,1.25 0.167,0.156 10 true ★
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Nut


Install the oil pan with the 17 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt A and B, and nut : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Standard Bolt:
Item Length
Bolt A 25 mm (0.98 in.)
Bolt B 45 mm (1.77 in.)
Bolt C 14 mm (0.55 in.)


NOTICE:

The bolts indicated by stars in the illustration are precoated parts. When reusing these bolts, apply adhesive to 2 or 3 threads before installation.


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



Hide 8.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer with the bolt and 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.

Remove any old seal packing (FIPG) and be careful not to drop any oil on the contact surfaces of the oil pan and No. 2 oil pan.


b.
A251904
2.879,1.364 3.109,1.552 0.229,0.188 10 *1 2.42,1.452 2.871,1.452 false
*1 Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan within 3 minutes after applying seal packing. After installing the oil pan, the oil pan bolts and nuts must be tightened within 15 minutes. Otherwise the seal packing must be removed and reapplied.

·

Do not start the engine for at least 4 hours after the installation.




c.

Install the No. 2 oil pan with the 14 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for nut : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 10.INSTALL CRANKSHAFT PULLEY

a.
A076309
1.438,1.042 2.948,0.917 2.948,0.917 2.083,1.448 true 3.021,0.823 3.354,0.979 0.333,0.156 10 false SST 3.021,1.646 3.208,1.833 0.188,0.188 10 false *a 0.958,1.865 1.135,2.031 0.177,0.167 10 false *b
*a Hold
*b Turn


Using SST, install the crankshaft pulley with the pulley set bolt.

SST
09213-54015  (91651-60855)
09330-00021  

Torque:
250 N*m (2549 kgf*cm, 184 ft.*lbf)


Hide 12.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 17.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 18.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)