Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2012.04
RM1840EF _51 Engine / Hybrid System _009577 1GR-FE ENGINE MECHANICAL _0052211 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

A076438
2.448,1.792 2.635,1.979 0.188,0.188 10 false *1
*1 "DOUBLE"


a.

Install the No. 1 idler pulley with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

HINT:

"DOUBLE" is marked on the No. 1 idler pulley to distinguish it from the No. 2 idler pulley.



Hide 2.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A112958
2.948,0.979 2.833,0.979 2.833,0.979 2.802,1.188 false 3,0.865 3.188,1.052 0.188,0.188 10 false *1 3.115,1.208 3.302,1.396 0.188,0.188 10 false *a
*1 New O-Ring
*a Push


Install a new O-ring to the engine oil level dipstick guide.


b.

Apply a light coat of engine oil to the O-ring.


c.

Push in the engine oil level dipstick guide end into the guide hole of the oil pan.


d.

Install the engine oil level dipstick guide with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


e.

Install the engine oil level dipstick.


Hide 5.INSTALL OIL FILLER CAP HOUSING

a.

Install a new gasket and the oil filler cap housing with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 6.INSTALL OIL FILLER CAP SUB-ASSEMBLY

Hide 8.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

A302378
2.646,0.531 2.802,0.729 0.156,0.198 10 false 1 2.75,1.427 2.906,1.625 0.156,0.198 10 false 2
V100135

Bolt A
V100136

Bolt B


a.

Temporarily install the V-ribbed belt tensioner with the 5 bolts.


b.

Install the V-ribbed belt tensioner by tightening bolt 1 and then bolt 2.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


c.

Tighten the other bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

Bolt Length:
Bolt Length
mm (in.)
A 70 mm (2.76 in.)
B 33 mm (1.30 in.)



Hide 9.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.

Install the front No. 1 engine mounting bracket LH with the 3 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 10.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.

Install the front No. 1 engine mounting bracket RH with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 12.INSTALL NO. 2 PCV HOSE

Hide 13.INSTALL PCV HOSE

Hide 14.INSTALL HEATER WATER HOSE

Hide 15.INSTALL ENGINE WIRE