When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
After removing the injection pipes, clean them with a brush and compressed air.
1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
3.DRAIN ENGINE COOLANT (w/ EGR Cooler)
4.REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler)
5.REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o EGR Cooler)
6.CHECK INJECTOR COMPENSATION CODE
If the injector compensation code is not correctly registered, it may cause malfunctions.
Read the injector compensation code.
w/ EGR Cooler: (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION)
w/o EGR Cooler: (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION)
Check that the compensation code of the installed injector is the same as the code registered in the ECM. If the code is not the same, register the injector compensation code on the injector.
w/ EGR Cooler: (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/ EGR Cooler)>REGISTRATION)
w/o EGR Cooler: (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION)
7.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)
8.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)
9.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY
After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
w/ EGR Cooler:
Remove the 2 nuts and No. 3 injection pipe clamp.
Remove the 2 bolts and 2 No. 2 injection pipe clamps.
| *a | Injector Side |
| *b | Common Rail Side |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| *1 | No. 2 Injection Pipe Clamp |
| *2 | No. 3 Injection Pipe Clamp |
| *a | Injector Side |
| *b | Common Rail Side |
w/o EGR Cooler:
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
10.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)
11.DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)
12.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)
13.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)
14.REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler)
15.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)
16.REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection pipe clamp with a new one.
w/ EGR Cooler:
Remove the bolt and disconnect the injection pipe clamp.
| *a | Injector Side |
| *b | Common Rail Side |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
w/o EGR Cooler:
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
| *a | Injector Side |
| *b | Common Rail Side |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
17.REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.
w/ EGR Cooler:
Remove the 3 bolts and disconnect the 4 injector connectors.
w/o EGR Cooler:
Disconnect the 4 injector connectors.
Disconnect the ventilation hose.
Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.
Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.
Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.
19.REMOVE INJECTOR ASSEMBLY
| *1 | Union Bolt |
Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
When removing the nozzle leakage pipe, place a cushion under the pipe.
Be careful not to deform or scratch the union seal surface.
After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.
Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.
Arrange the injectors, No. 1 nozzle holder clamps, washers and bolts in the correct order.
Remove the O-ring from each injector.
Remove the 4 injection nozzle seats from the cylinder head.