Home › Engine / Hybrid System › 1GR-FE FUEL › FUEL INJECTOR › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009582 1GR-FE FUEL _0052264 FUEL INJECTOR A

1GR-FE FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL INJECTOR ASSEMBLY

A075654
2.75,0.917 2.323,0.344 2.323,0.344 2.01,0.344 false 1.031,1.792 0.802,1.792 0.802,1.792 0.646,1.448 false 1.104,1.698 1.344,1.896 0.24,0.198 10 false *2 1.802,0.26 2.021,0.458 0.219,0.198 10 false *1
*1 New Insulator
*2 New O-Ring


a.

Install a new insulator to each fuel injector.


b.

Apply a light coat of spindle oil or gasoline to a new O-ring and install it to each fuel injector.


c.
A250901
0.54,0.378 0.71,0.548 0.17,0.17 10 *1 0.748,0.455 1.003,0.455 1.003,0.455 1.421,0.748 false
*1 Connector
V100135

Outward
V100136

Turn
V100137

Push


Install the 6 fuel injectors.

i.

While turning the fuel injector left and right, install it to the fuel delivery pipe.


ii.

Position the fuel injectors with the connectors facing outward.



Hide 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.

Place the fuel delivery pipe together with the 6 fuel injectors on the intake manifold.


b.

Temporarily install the 6 bolts which are used to hold the fuel delivery pipe to the intake manifold.


c.
A075656
1.948,1.573 1.271,1.313 1.271,1.313 0.844,1.313 true 0.646,1.219 0.844,1.396 0.198,0.177 10 false *1
*1 Connector
V100135

Turn


Check that the fuel injectors rotate smoothly.

If the fuel injectors do not rotate smoothly, replace the O-ring of any fuel injector that does not rotate smoothly.


d.

Position the fuel injector connector outward.


e.

Tighten the 6 bolts which are used to hold the fuel delivery pipe to the intake manifold.

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


f.

Connect the 6 fuel injector connectors.


Hide 3.CONNECT NO. 2 FUEL PIPE SUB-ASSEMBLY

a.

Connect the No. 2 fuel pipe sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 4.CONNECT NO. 1 FUEL PIPE SUB-ASSEMBLY

a.

Connect the No. 1 fuel pipe sub-assembly (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 7.INSPECT FOR FUEL LEAK

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the intelligent tester to the DLC3.


ii.

Turn the ignition switch to ON and turn the intelligent tester on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 61 5

iv.

Check that there are no leaks from the fuel system.

If there are fuel leaks, repair or replace parts as necessary.


v.

Turn the ignition switch off.


vi.

Disconnect the intelligent tester from the DLC3.