Home › Engine / Hybrid System › 2KD-FTV EMISSION CONTROL › EGR VALVE(w/o DPF) › 2011.10–2012.01
RM1840EF _51 Engine / Hybrid System _009583 2KD-FTV EMISSION CONTROL _0052274 EGR VALVE(w/o DPF) A

2KD-FTV EMISSION CONTROL  EGR VALVE(w/o DPF)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.DRAIN ENGINE COOLANT (w/ EGR Cooler)

Hide 5.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

a.
A147224
0.688,0.167 0.885,0.167 0.885,0.167 1.01,0.677 true 2.531,1.531 2.021,1.531 true 0.5,0.063 0.688,0.219 0.188,0.156 10 false *1 2.583,1.427 2.771,1.583 0.188,0.156 10 false *2
*1 No. 4 Water By-pass Hose
*2 No. 3 Water By-pass Hose


Remove the clamp.


b.

Disconnect the No. 3 water by-pass hose from the EGR cooler.


Hide 6.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

a.

Disconnect the No. 4 water by-pass hose from the EGR cooler.


Hide 7.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 8.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

a.
A147215

Remove the 3 bolts and No. 2 intake air connector bracket.


Hide 9.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/o EGR Cooler)

Hide 10.DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)

a.
A147216

Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.


Hide 11.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (for EGR)

a.

w/ EGR Cooler:

i.
A147217

Disconnect the 2 connectors.


ii.
A147218

Disconnect the 5 vacuum hoses.


iii.

Remove the bolt and No. 1 gas filter with the gas filter bracket.


iv.
A147231

Remove the 2 bolts and electric vacuum regulating valve bracket together with the vacuum damper.

NOTICE:

Do not remove the electric vacuum regulating valve from the bracket.




b.

w/o EGR Cooler:

i.
A212373

Disconnect the connector.


ii.

Disconnect the 2 vacuum hoses.


iii.

Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

NOTICE:

Do not remove the electric vacuum regulating valve from the bracket.




Hide 12.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.
A147230

Remove the 3 nuts, No. 2 intake air connector and gasket.


Hide 13.REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.
A147219

Remove the 3 bolts, intake air connector and 2 gaskets.


Hide 15.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

a.
A147220

Disconnect the vacuum hose from the No. 2 EGR valve.


b.
A147225

Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.


c.

Remove the gasket from the cylinder head.


Hide 16.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.
G037199
0.333,0.74 0.479,0.74 0.479,0.74 0.677,1.177 true 1.625,0.104 1.75,0.104 1.75,0.104 2,0.26 true 0.115,0.667 0.302,0.823 0.188,0.156 10 true *1 1.438,0.031 1.625,0.188 0.188,0.156 10 true *1
*1 Gasket


Remove the 2 bolts, 2 nuts, No. 1 EGR pipe and 2 gaskets.


Hide 17.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

w/ EGR Cooler:

i.
A151125

Remove the 2 bolts, electric EGR control valve and gasket.



b.

w/o EGR Cooler:

i.

Disconnect the EGR valve position sensor connector.


ii.

Remove the electric EGR control valve and gasket.



Hide 18.REMOVE EGR VALVE ADAPTER (w/ EGR Cooler)

a.
A147221

Using a 6 mm hexagon wrench, remove the 3 hexagon bolts, 3 plate washers, EGR valve adapter and gasket.


Hide 19.REMOVE NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)

a.
A147222

Using a 5 mm hexagon wrench, remove the hexagon bolt, No. 2 EGR valve and gasket.