Home › Engine / Hybrid System › 1KD-FTV EMISSION CONTROL › EGR VALVE(w/o Glow Plug Controller) › 2012.01–2012.04
RM1840EF _51 Engine / Hybrid System _009584 1KD-FTV EMISSION CONTROL _0052287 EGR VALVE(w/o Glow Plug Controller) A

1KD-FTV EMISSION CONTROL  EGR VALVE(w/o Glow Plug Controller)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes, clean them with a brush and compressed air.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.DRAIN ENGINE COOLANT (w/ EGR Cooler)

Hide 5.DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)

a.
A147224
0.688,0.167 0.885,0.167 0.885,0.167 1.01,0.677 true 2.531,1.531 2.021,1.531 true 0.5,0.063 0.688,0.219 0.188,0.156 10 false *1 2.583,1.427 2.771,1.583 0.188,0.156 10 false *2
*1 No. 4 Water By-pass Hose
*2 No. 3 Water By-pass Hose


Remove the clamp.


b.

Disconnect the No. 3 water by-pass hose from the EGR cooler.


Hide 6.DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)

a.

Disconnect the No. 4 water by-pass hose from the EGR cooler.


Hide 7.REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/ EGR Cooler)

Hide 8.REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)

a.
A147215

Remove the 3 bolts and No. 2 intake air connector bracket.


Hide 10.DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)

a.
A147216

Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.


Hide 11.REMOVE NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler)

Hide 12.REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY

Hide 13.REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.
A147230

Remove the 3 nuts, No. 2 intake air connector and gasket.


Hide 14.REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler)

a.
A147219

Remove the 3 bolts, intake air connector and 2 gaskets.


Hide 16.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)

a.

Disconnect the EGR valve position sensor connector.


b.
A147220

Disconnect the vacuum hose from the No. 2 EGR valve.


c.
A147225

Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.


d.

Remove the gasket from the cylinder head.


Hide 17.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY (w/o EGR Cooler)

a.
G037199
0.333,0.74 0.479,0.74 0.479,0.74 0.677,1.177 true 1.625,0.104 1.75,0.104 1.75,0.104 2,0.26 true 0.115,0.667 0.302,0.823 0.188,0.156 10 true *1 1.438,0.031 1.625,0.188 0.188,0.156 10 true *1
*1 Gasket


Remove the 2 bolts, 2 nuts, No. 1 EGR pipe and 2 gaskets.


Hide 18.REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

w/ EGR Cooler:

i.
A151125

Remove the 2 bolts, electric EGR control valve and gasket.



b.

w/o EGR Cooler:

i.

Remove the electric EGR control valve and gasket.



Hide 19.REMOVE EGR VALVE ADAPTER (w/ EGR Cooler)

a.
A147221

Using a 6 mm hexagon wrench, remove the 3 hexagon bolts, 3 plate washers, EGR valve adapter and gasket.


Hide 20.REMOVE NO. 2 EGR VALVE ASSEMBLY (w/ EGR Cooler)

a.
A147222

Using a 5 mm hexagon wrench, remove the hexagon bolt, No. 2 EGR valve and gasket.