Home › Engine / Hybrid System › 1KD-FTV INTAKE / EXHAUST › INTAKE MANIFOLD(w/ Glow Plug Controller) › 2012.04–2012.10
RM1840EF _51 Engine / Hybrid System _009588 1KD-FTV INTAKE / EXHAUST _0052328 INTAKE MANIFOLD(w/ Glow Plug Controller) A

1KD-FTV INTAKE / EXHAUST  INTAKE MANIFOLD(w/ Glow Plug Controller)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.

·

After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.



PROCEDURE

Hide 1.INSTALL INTAKE MANIFOLD

a.
A301701
0.625,1.927 0.823,2.146 0.198,0.219 10 false 1 3.177,0.708 3.333,0.906 0.156,0.198 10 false 2 1.646,1.917 1.875,2.135 0.229,0.219 10 false 3 2.833,1.917 2.99,2.115 0.156,0.198 10 false 4 2.229,1.75 2.385,1.948 0.156,0.198 10 false 5 1.063,1.75 1.323,2.042 0.26,0.292 10 false 6

Temporarily install a new gasket and the intake manifold with the 4 bolts and 2 nuts.


b.

Tighten the 4 bolts and 2 nuts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

Make sure that the swirl control valve actuator is not damaged by the surrounding parts.



c.

Attach the sensor wire connector clamp.


d.

for DPF:

Connect the vacuum hose to the intake manifold.


Hide 2.INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for i-ART)

a.
A271924
2.75,0.323 2.615,0.323 2.615,0.323 1.979,0.698 true 0.677,0.417 0.781,0.417 0.781,0.417 1.292,0.833 false 0.698,1.292 0.792,1.292 0.792,1.292 1.5,1.01 true 1.865,0.938 2.5,1.333 2.5,1.333 2.594,1.333 true 0.521,0.313 0.75,0.531 0.229,0.219 10 false *1 2.781,0.219 3.01,0.438 0.229,0.219 10 false *2 0.531,1.188 0.76,1.406 0.229,0.219 10 false *a 2.615,1.229 2.844,1.448 0.229,0.219 10 false *b
*1 No. 1 vacuum switching valve
*2 No. 2 vacuum switching valve
*a Dark Blue Color
*b Brown Color


Install the No. 1 vacuum switching valve and No. 2 vacuum switching valve with the 2 screws.

Torque:
3.5 N*m (36 kgf*cm, 31 in.*lbf)


b.

Connect the 4 vacuum hoses.


Hide 4.INSTALL INTAKE MANIFOLD INSULATOR

Hide 5.INSTALL NO. 1 INTAKE MANIFOLD INSULATOR

Hide 8.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET

a.

Install the No. 3 intercooler support bracket with the bolt.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 12.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (for DPF)

Hide 16.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER

Hide 17.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).