Home › Drivetrain › A340F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY › from 2012.10
RM1840EF _52 Drivetrain _009609 A340F AUTOMATIC TRANSMISSION / TRANSAXLE _0052458 AUTOMATIC TRANSMISSION ASSEMBLY A

A340F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 4.REMOVE SHIFT LEVER BOOT ASSEMBLY

a.
C239519

Remove the 4 screws and shift lever boot assembly.


Hide 5.REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY

a.
C213734

Fold back the transfer front drive shift boot.


b.

Using needle-nose pliers, remove the snap ring and pull out the shift lever.

HINT:

Move the transfer shift lever to the H4 position.



Hide 6.REMOVE NO. 1 ENGINE UNDER COVER

Hide 7.REMOVE NO. 2 ENGINE UNDER COVER

Hide 11.DRAIN AUTOMATIC TRANSMISSION FLUID

a.

Remove the drain plug and gasket, and drain ATF.


b.

Install a new gasket and the drain plug.

Torque:
20 N*m (205 kgf*cm, 15 ft.*lbf)


Hide 12.REMOVE TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY

C283130

a.

Remove the oil dipstick.


b.

Remove the 2 bolts and oil filler tube.


c.

Remove the O-ring from the oil filler tube.


Hide 13.DISCONNECT OIL COOLER TUBE

G034850

a.

Using a union nut wrench, disconnect the inlet tube and outlet tube.


b.
G034255

Remove the 3 bolts and 3 clamps.


Hide 14.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

G034515

a.

Remove the nut and disconnect the control cable.


b.

Remove the clip and disconnect the control cable.


Hide 15.DISCONNECT GROUND CABLE

a.
C239525

Remove the nut and disconnect the ground cable.


Hide 17.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

G034518

a.

Support the transmission with a transmission jack.


Hide 18.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034256

a.

Remove the 4 set bolts of the No. 1 engine mounting insulator rear.


b.

Remove the 4 nuts, 4 bolts and frame crossmember.


Hide 19.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
G034260

Remove the 4 bolts and engine mounting insulator.


Hide 20.DISCONNECT ENGINE WIRE

G034519

a.

Tilt the transmission downward.

NOTICE:

Make sure the cooling fan does not contact the fan shroud.



b.

Disconnect the 5 connectors and detach the 6 clamps.

C236146
0.063,0.083 0.365,0.281 0.302,0.198 10 false *A 3.573,0.083 3.927,0.292 0.354,0.208 10 false *B
*A LH Side *B RH Side


i.

Disconnect the 5 connectors.



Hide 21.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the bolt and wire harness clamp bracket from the transmission.


Hide 22.REMOVE STIFFENER PLATE

a.

Remove the 4 bolts and stiffener plate RH (with clamp).

C283131
0.083,0.104 0.396,0.26 0.313,0.156 10 false *A 3.667,0.125 3.979,0.281 0.313,0.156 10 false *B
*A LH Side *B RH Side



b.

Remove the 4 bolts and stiffener plate LH.


c.

Remove the No. 4 cylinder block insulator.


d.

Remove the No. 2 end plate.


Hide 23.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

G034258

a.

Turn the crankshaft to gain access to each bolt.


b.

Hold the crankshaft pulley bolt with a wrench, and remove the 6 torque converter clutch mounting bolts.


c.
C283132
0.708,1.24 0.49,1.042 0.49,1.042 0.365,1.042 true 2.51,1.292 2.823,0.969 2.823,0.969 3,0.969 true 0.146,0.948 0.458,1.104 0.313,0.156 10 false *1 3.083,0.875 3.396,1.031 0.313,0.156 10 false *1
*1 Knock Pin


Remove the 5 bolts and transmission from the engine.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transmission assembly and engine assembly.



Hide 24.REMOVE TRANSMISSION CONTROL CABLE BRACKET

G034516

a.

Remove the 2 bolts and control cable bracket from the transmission.


Hide 26.REMOVE TORQUE CONVERTER ASSEMBLY