Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) › from 2012.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052508 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV without i-ART)  U0100  Lost Communication with ECM / PCM "A"  


DESCRIPTION

The ECM communicates with the TCM using the Controller Area Network (CAN).

If there is a problem with this communication, the TCM stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
U0100 Lost Communication with ECM / PCM "A" All conditions are met for 1.25 seconds (1-trip detection logic):
·

Ignition switch is ON.

·

Battery voltage is 10.5 V or higher.

·

There is no communication between the ECM and TCM.


·

Harness or connector

·

ECM

·

TCM


Comes on DTC stored

WIRING DIAGRAM

C217589
5.833,3.094 6.229,3.292 0.396,0.198 10 false TCM 5.625,1.24 6.125,1.438 0.5,0.198 10 false CAN+ 5.823,2.927 6.125,3.125 0.302,0.198 10 false G41 5.344,1.365 5.625,1.563 0.281,0.198 10 false 21 5.625,2.219 6.125,2.417 0.5,0.198 10 false CAN- 5.344,2.344 5.625,2.542 0.281,0.198 10 false 20 1.854,3.094 2.25,3.292 0.396,0.198 10 false ECM 1.854,2.938 2.396,3.135 0.542,0.198 10 false G38 1.969,1.24 2.469,1.438 0.5,0.198 10 false CAN+ 2.469,1.365 2.75,1.563 0.281,0.198 10 false 22 2,2.198 2.5,2.396 0.5,0.198 10 false CAN- 2.479,2.333 2.76,2.531 0.281,0.198 10 false 21

CAUTION / NOTICE / HINT

HINT:
·

Refer to the inspection procedure for the CAN communication system.

·

If the CAN communication malfunctions, the TCM cannot receive current data from the ECM. In this case, the freeze frame data output from the TCM has not been updated so the data will not be useful for the inspection. However, reading the Data List as the first step in troubleshooting is an effective way to find malfunctions.

·

The malfunctioning area can be confirmed using the Bus Check function of the intelligent tester (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - TCM)
a.

Disconnect the C38 ECM connector.


b.

Disconnect the G41 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G38-22 (CAN+) - G41-21 (CAN+) Always Below 1 Ω
G38-21 (CAN-) - G41-20 (CAN-) Always Below 1 Ω
G38-22 (CAN+) or G41-21 (CAN+) - Body ground or other terminals Always 10 kΩ or higher
G38-21 (CAN-) or G41-20 (CAN-) - Body ground or other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK IF DTC OUTPUT RECURS (DTC U0100)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK IF DTC OUTPUT RECURS (DTC U0100)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes / Clear.

Powertrain > ECT > Clear DTCs
50002 64

e.

Replace the TCM.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TCM(for 1KD-FTV)>REMOVAL

HINT:

Replace the TCM with the TCM of a normally functioning vehicle of the same model.



f.

Start the engine.


g.

Enter the following menus: Powertrain / ECT / Trouble Codes.

Powertrain > ECT > Trouble Codes
50001 64

h.

Read the DTCs using the tester.

Result:
Result Proceed to
U0100 is output A
DTCs are not output B




A

B